linux-stable.git/arch/mips, branch v4.4.232

MIPS: Fix build for LTS kernel caused by backporting lpj adjustment

2020-07-22T07:10:07+00:00

Commit ed26aacfb5f71eecb20a ("mips: Add udelay lpj numbers adjustment")
has backported to 4.4~5.4, but the "struct cpufreq_freqs" (and also the
cpufreq notifier machanism) of 4.4~4.19 are different from the upstream
kernel. These differences cause build errors, and this patch can fix the
build.

Cc: Serge Semin 
Cc: Stable  # 4.4/4.9/4.14/4.19
Signed-off-by: Huacai Chen 
Signed-off-by: Greg Kroah-Hartman

MIPS: Add missing EHB in mtc0 -> mfc0 sequence for DSPen

2020-07-09T07:35:09+00:00

commit fcec538ef8cca0ad0b84432235dccd9059c8e6f8 upstream.

This resolves the hazard between the mtc0 in the change_c0_status() and
the mfc0 in configure_exception_vector(). Without resolving this hazard
configure_exception_vector() could read an old value and would restore
this old value again. This would revert the changes change_c0_status()
did. I checked this by printing out the read_c0_status() at the end of
per_cpu_trap_init() and the ST0_MX is not set without this patch.

The hazard is documented in the MIPS Architecture Reference Manual Vol.
III: MIPS32/microMIPS32 Privileged Resource Architecture (MD00088), rev
6.03 table 8.1 which includes:

   Producer | Consumer | Hazard
  ----------|----------|----------------------------
   mtc0     | mfc0     | any coprocessor 0 register

I saw this hazard on an Atheros AR9344 rev 2 SoC with a MIPS 74Kc CPU.
There the change_c0_status() function would activate the DSPen by
setting ST0_MX in the c0_status register. This was reverted and then the
system got a DSP exception when the DSP registers were saved in
save_dsp() in the first process switch. The crash looks like this:

[    0.089999] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.097796] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.107070] Kernel panic - not syncing: Unexpected DSP exception
[    0.113470] Rebooting in 1 seconds..

We saw this problem in OpenWrt only on the MIPS 74Kc based Atheros SoCs,
not on the 24Kc based SoCs. We only saw it with kernel 5.4 not with
kernel 4.19, in addition we had to use GCC 8.4 or 9.X, with GCC 8.3 it
did not happen.

In the kernel I bisected this problem to commit 9012d011660e ("compiler:
allow all arches to enable CONFIG_OPTIMIZE_INLINING"), but when this was
reverted it also happened after commit 172dcd935c34b ("MIPS: Always
allocate exception vector for MIPSr2+").

Commit 0b24cae4d535 ("MIPS: Add missing EHB in mtc0 -> mfc0 sequence.")
does similar changes to a different file. I am not sure if there are
more places affected by this problem.

Signed-off-by: Hauke Mehrtens 
Cc: 
Signed-off-by: Thomas Bogendoerfer 
Signed-off-by: Greg Kroah-Hartman

MIPS: Fix IRQ tracing when call handle_fpe() and handle_msa_fpe()

2020-06-20T08:23:22+00:00

[ Upstream commit 31e1b3efa802f97a17628dde280006c4cee4ce5e ]

Register "a1" is unsaved in this function,
 when CONFIG_TRACE_IRQFLAGS is enabled,
 the TRACE_IRQS_OFF macro will call trace_hardirqs_off(),
 and this may change register "a1".
 The changed register "a1" as argument will be send
 to do_fpe() and do_msa_fpe().

Signed-off-by: YuanJunQing 
Signed-off-by: Thomas Bogendoerfer 
Signed-off-by: Sasha Levin

mips: Add udelay lpj numbers adjustment

2020-06-20T08:23:21+00:00

[ Upstream commit ed26aacfb5f71eecb20a51c4467da440cb719d66 ]

Loops-per-jiffies is a special number which represents a number of
noop-loop cycles per CPU-scheduler quantum - jiffies. As you
understand aside from CPU-specific implementation it depends on
the CPU frequency. So when a platform has the CPU frequency fixed,
we have no problem and the current udelay interface will work
just fine. But as soon as CPU-freq driver is enabled and the cores
frequency changes, we'll end up with distorted udelay's. In order
to fix this we have to accordinly adjust the per-CPU udelay_val
(the same as the global loops_per_jiffy) number. This can be done
in the CPU-freq transition event handler. We subscribe to that event
in the MIPS arch time-inititalization method.

Co-developed-by: Alexey Malahov 
Signed-off-by: Alexey Malahov 
Signed-off-by: Serge Semin 
Reviewed-by: Jiaxun Yang 
Cc: Thomas Bogendoerfer 
Cc: Paul Burton 
Cc: Ralf Baechle 
Cc: Arnd Bergmann 
Cc: Rob Herring 
Cc: devicetree@vger.kernel.org
Signed-off-by: Thomas Bogendoerfer 
Signed-off-by: Sasha Levin

mips: cm: Fix an invalid error code of INTVN_*_ERR

2020-06-20T08:23:21+00:00

[ Upstream commit 8a0efb8b101665a843205eab3d67ab09cb2d9a8d ]

Commit 3885c2b463f6 ("MIPS: CM: Add support for reporting CM cache
errors") adds cm2_causes[] array with map of error type ID and
pointers to the short description string. There is a mistake in
the table, since according to MIPS32 manual CM2_ERROR_TYPE = {17,18}
correspond to INTVN_WR_ERR and INTVN_RD_ERR, while the table
claims they have {0x17,0x18} codes. This is obviously hex-dec
copy-paste bug. Moreover codes {0x18 - 0x1a} indicate L2 ECC errors.

Fixes: 3885c2b463f6 ("MIPS: CM: Add support for reporting CM cache errors")
Signed-off-by: Serge Semin 
Cc: Alexey Malahov 
Cc: Thomas Bogendoerfer 
Cc: Paul Burton 
Cc: Ralf Baechle 
Cc: Arnd Bergmann 
Cc: Rob Herring 
Cc: linux-pm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Thomas Bogendoerfer 
Signed-off-by: Sasha Levin

MIPS: Make sparse_init() using top-down allocation

2020-06-20T08:23:20+00:00

[ Upstream commit 269b3a9ac538c4ae87f84be640b9fa89914a2489 ]

In the current code, if CONFIG_SWIOTLB is set, when failed to get IO TLB
memory from the low pages by plat_swiotlb_setup(), it may lead to the boot
process failed with kernel panic.

(1) On the Loongson and SiByte platform
arch/mips/loongson64/dma.c
arch/mips/sibyte/common/dma.c
void __init plat_swiotlb_setup(void)
{
	swiotlb_init(1);
}

kernel/dma/swiotlb.c
void  __init
swiotlb_init(int verbose)
{
...
	vstart = memblock_alloc_low(PAGE_ALIGN(bytes), PAGE_SIZE);
	if (vstart && !swiotlb_init_with_tbl(vstart, io_tlb_nslabs, verbose))
		return;
...
	pr_warn("Cannot allocate buffer");
	no_iotlb_memory = true;
}

phys_addr_t swiotlb_tbl_map_single()
{
...
	if (no_iotlb_memory)
		panic("Can not allocate SWIOTLB buffer earlier ...");
...
}

(2) On the Cavium OCTEON platform
arch/mips/cavium-octeon/dma-octeon.c
void __init plat_swiotlb_setup(void)
{
...
	octeon_swiotlb = memblock_alloc_low(swiotlbsize, PAGE_SIZE);
	if (!octeon_swiotlb)
		panic("%s: Failed to allocate %zu bytes align=%lx\n",
		      __func__, swiotlbsize, PAGE_SIZE);
...
}

Because IO_TLB_DEFAULT_SIZE is 64M, if the rest size of low memory is less
than 64M when call plat_swiotlb_setup(), we can easily reproduce the panic
case.

In order to reduce the possibility of kernel panic when failed to get IO
TLB memory under CONFIG_SWIOTLB, it is better to allocate low memory as
small as possible before plat_swiotlb_setup(), so make sparse_init() using
top-down allocation.

Reported-by: Juxin Gao 
Co-developed-by: Juxin Gao 
Signed-off-by: Juxin Gao 
Signed-off-by: Tiezhu Yang 
Signed-off-by: Thomas Bogendoerfer 
Signed-off-by: Sasha Levin

MIPS: perf: Remove incorrect odd/even counter handling for I6400

2020-05-10T08:26:24+00:00

commit f7a31b5e7874f77464a4eae0a8ba84b9ae0b3a54 upstream.

All performance counters on I6400 (odd and even) are capable of counting
any of the available events, so drop current logic of using the extra
bit to determine which counter to use.

Signed-off-by: Marcin Nowakowski 
Fixes: 4e88a8621301 ("MIPS: Add cases for CPU_I6400")
Fixes: fd716fca10fc ("MIPS: perf: Fix I6400 event numbers")
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15991/
Signed-off-by: Ralf Baechle 
Signed-off-by: Greg Kroah-Hartman

mips/panic: replace smp_send_stop() with kdump friendly version in panic path

2020-05-10T08:25:46+00:00

commit 54c721b857fd45f3ad3bda695ee4f472518db02a upstream.

Daniel Walker reported problems which happens when
crash_kexec_post_notifiers kernel option is enabled
(https://lkml.org/lkml/2015/6/24/44).

In that case, smp_send_stop() is called before entering kdump routines
which assume other CPUs are still online.  As the result, kdump
routines fail to save other CPUs' registers.  Additionally for MIPS
OCTEON, it misses to stop the watchdog timer.

To fix this problem, call a new kdump friendly function,
crash_smp_send_stop(), instead of the smp_send_stop() when
crash_kexec_post_notifiers is enabled.  crash_smp_send_stop() is a
weak function, and it just call smp_send_stop().  Architecture
codes should override it so that kdump can work appropriately.
This patch provides MIPS version.

Fixes: f06e5153f4ae (kernel/panic.c: add "crash_kexec_post_notifiers" option)
Link: http://lkml.kernel.org/r/20160810080950.11028.28000.stgit@sysi4-13.yrl.intra.hitachi.co.jp
Signed-off-by: Hidehiro Kawai 
Reported-by: Daniel Walker 
Cc: Dave Young 
Cc: Baoquan He 
Cc: Vivek Goyal 
Cc: Eric Biederman 
Cc: Masami Hiramatsu 
Cc: Daniel Walker 
Cc: Xunlei Pang 
Cc: Thomas Gleixner 
Cc: Ingo Molnar 
Cc: "H. Peter Anvin" 
Cc: Borislav Petkov 
Cc: David Vrabel 
Cc: Toshi Kani 
Cc: Ralf Baechle 
Cc: David Daney 
Cc: Aaro Koskinen 
Cc: "Steven J. Hill" 
Cc: Corey Minyard 
Signed-off-by: Andrew Morton 
Signed-off-by: Linus Torvalds 
Signed-off-by: Greg Kroah-Hartman

MIPS: Define AT_VECTOR_SIZE_ARCH for ARCH_DLINFO

2020-05-10T08:25:46+00:00

commit 233b2ca181f20674ecad11be90b00814911ce345 upstream.

AT_VECTOR_SIZE_ARCH should be defined with the maximum number of
NEW_AUX_ENT entries that ARCH_DLINFO can contain, but it wasn't defined
for MIPS at all even though ARCH_DLINFO will contain one NEW_AUX_ENT for
the VDSO address.

This shouldn't be a problem as AT_VECTOR_SIZE_BASE includes space for
AT_BASE_PLATFORM which MIPS doesn't use, but lets define it now and add
the comment above ARCH_DLINFO as found in several other architectures to
remind future modifiers of ARCH_DLINFO to keep AT_VECTOR_SIZE_ARCH up to
date.

Fixes: ebb5e78cc634 ("MIPS: Initial implementation of a VDSO")
Signed-off-by: James Hogan 
Cc: linux-mips@linux-mips.org
Cc: linux-arch@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13823/
Signed-off-by: Ralf Baechle 
Signed-off-by: Greg Kroah-Hartman

MIPS: RM7000: Double locking bug in rm7k_tc_disable()

2020-05-10T08:25:46+00:00

commit 58a7e1c140f3ad61646bc0cd9a1f6a9cafc0b225 upstream.

We obviously intended to enable IRQs again at the end.

Fixes: 745aef5df1e2 ('MIPS: RM7000: Add support for tertiary cache')
Signed-off-by: Dan Carpenter 
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: kernel-janitors@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13815/
Signed-off-by: Ralf Baechle 
Signed-off-by: Greg Kroah-Hartman