Based on 1 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license as published by
  the free software foundation either version 2 of the license or at
  your option any later version

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-or-later

has been chosen to replace the boilerplate/reference in 3029 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull MIPS updates from Paul Burton:

 - Support for the MIPSr6 MemoryMapID register & Global INValidate TLB
   (GINVT) instructions, allowing for more efficient TLB maintenance
   when running on a CPU such as the I6500 that supports these.

 - Enable huge page support for MIPS64r6.

 - Optimize post-DMA cache sync by removing that code entirely for
   kernel configurations in which we know it won't be needed.

 - The number of pages allocated for interrupt stacks is now calculated
   correctly, where before we would wastefully allocate too much memory
   in some configurations.

 - The ath79 platform migrates to devicetree.

 - The bcm47xx platform sees fixes for the Buffalo WHR-G54S board.

 - The ingenic/jz4740 platform gains support for appended devicetrees.

 - The cavium_octeon, lantiq, loongson32 & sgi-ip27 platforms all see
   cleanups as do various pieces of core architecture code.

* tag 'mips_5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (66 commits)
  MIPS: lantiq: Remove separate GPHY Firmware loader
  MIPS: ingenic: Add support for appended devicetree
  MIPS: SGI-IP27: rework HUB interrupts
  MIPS: SGI-IP27: do boot CPU init later
  MIPS: SGI-IP27: do xtalk scanning later
  MIPS: SGI-IP27: use pr_info/pr_emerg and pr_cont to fix output
  MIPS: SGI-IP27: clean up bridge access and header files
  MIPS: SGI-IP27: get rid of volatile and hubreg_t
  MIPS: irq: Allocate accurate order pages for irq stack
  MIPS: dma-noncoherent: Remove bogus condition in dma_sync_phys()
  MIPS: eBPF: Remove REG_32BIT_ZERO_EX
  MIPS: eBPF: Always return sign extended 32b values
  MIPS: CM: Fix indentation
  MIPS: BCM47XX: Fix/improve Buffalo WHR-G54S support
  MIPS: OCTEON: program rx/tx-delay always from DT
  MIPS: OCTEON: delete board-specific link status
  MIPS: OCTEON: don't lie about interface type of CN3005 board
  MIPS: OCTEON: warn if deprecated link status is being used
  MIPS: OCTEON: add fixed-link nodes to in-kernel device tree
  MIPS: Delete unused flush_cache_sigtramp()
  ...

mips_cm_error_report() contains a function call that's incorrectly
indented a level further than it ought to be. Remove a tab from the
start of both affected lines.

Signed-off-by: Paul Burton <paul.burton@mips.com>

Accordingly to the documentation
---cut---
The GCR_ERROR_CAUSE.ERR_TYPE field and the GCR_ERROR_MULT.ERR_TYPE
fields can be cleared by either a reset or by writing the current
value of GCR_ERROR_CAUSE.ERR_TYPE to the
GCR_ERROR_CAUSE.ERR_TYPE register.
---cut---
Do exactly this. Original value of cm_error may be safely written back;
it clears error cause and keeps other bits untouched.

Fixes: 3885c2b463f6 ("MIPS: CM: Add support for reporting CM cache errors")
Signed-off-by: Vladimir Kondratiev <vladimir.kondratiev@linux.intel.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: stable@vger.kernel.org # v4.3+

Since commit 68923cdc2eb3 ("MIPS: CM: Add cluster & block args to
mips_cm_lock_other()"), mips_smp_send_ipi_mask() has used
mips_cm_lock_other_cpu() with each CPU number, rather than
mips_cm_lock_other() with the first VPE in each core. Prior to r6,
multicore multithreaded systems such as dual-core dual-thread
interAptivs with CPU Idle enabled (e.g. MIPS Creator Ci40) results in
mips_cm_lock_other() repeatedly hitting WARN_ON(vp != 0).

There doesn't appear to be anything fundamentally wrong about passing a
non-zero VP/VPE number, even if it is a core's region that is locked
into the other region before r6, so remove that particular WARN_ON().

Fixes: 68923cdc2eb3 ("MIPS: CM: Add cluster & block args to mips_cm_lock_other()")
Signed-off-by: James Hogan <jhogan@kernel.org>
Reviewed-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org # 4.14+
Patchwork: https://patchwork.linux-mips.org/patch/17883/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS will soon not be a part of Imagination Technologies, and as such
many @imgtec.com email addresses will no longer be valid. This patch
updates the addresses for those who:

 - Have 10 or more patches in mainline authored using an @imgtec.com
   email address, or any patches dated within the past year.

 - Are still with Imagination but leaving as part of the MIPS business
   unit, as determined from an internal email address list.

 - Haven't already updated their email address (ie. JamesH) or expressed
   a desire to be excluded (ie. Maciej).

 - Acked v2 or earlier of this patch, which leaves Deng-Cheng, Matt &
   myself.

New addresses are of the form firstname.lastname@mips.com, and all
verified against an internal email address list.  An entry is added to
.mailmap for each person such that get_maintainer.pl will report the new
addresses rather than @imgtec.com addresses which will soon be dead.

Instances of the affected addresses throughout the tree are then
mechanically replaced with the new @mips.com address.

Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@mips.com>
Acked-by: Dengcheng Zhu <dengcheng.zhu@mips.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Matt Redfearn <matt.redfearn@mips.com>
Acked-by: Matt Redfearn <matt.redfearn@mips.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: trivial@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

With Coherence Manager (CM) 3.5 information about the topology of the
system, which has previously only been available through & accessed from
the CM, is now also provided by the Cluster Power Controller (CPC). This
includes a new CPC_CONFIG register mirroring GCR_CONFIG, and similarly a
new CPC_Cx_CONFIG register mirroring GCR_Cx_CONFIG.

In preparation for adjusting functions such as mips_cm_numcores(), which
have previously only needed to access the CM, to also access the CPC
this patch modifies the way we use the various CPS headers. Rather than
having users include asm/mips-cm.h or asm/mips-cpc.h individually we
instead have users include asm/mips-cps.h which in turn includes
asm/mips-cm.h & asm/mips-cpc.h. This means that users will gain access
to both CM & CPC registers by including one header, and most importantly
it makes asm/mips-cps.h an ideal location for helper functions which
need to access the various components of the CPS.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17015/
Patchwork: https://patchwork.linux-mips.org/patch/17217/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

With CM >= 3.5 we have the notion of multiple clusters & can access
their CM, CPC & GIC registers via the apporpriate redirect/other
register blocks. In order to allow for this introduce cluster & block
arguments to mips_cm_lock_other() which configures the redirect/other
region to point at the appropriate cluster, core, VP & register block.

Since we now have 4 arguments to mips_cm_lock_other() & a common use is
likely to be to target the cluster, core & VP corresponding to a
particular Linux CPU number we also add a new mips_cm_lock_other_cpu()
helper function which handles that without the caller needing to
manually pull out the cluster, core & VP numbers.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17013/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

We currently have fields in struct cpuinfo_mips for the core & VP(E) ID
of a particular CPU, and various pieces of code directly access those
fields. This patch abstracts such access by introducing accessor
functions cpu_core(), cpu_set_core(), cpu_vpe_id() & cpu_set_vpe_id()
and having code that needs to access these values call those functions
rather than directly accessing the struct cpuinfo_mips fields. This
prepares us for changes to the way in which those values are stored in
later patches.

The cpu_vpe_id() function is introduced even though we already had a
cpu_vpe_id() macro for a couple of reasons:

  1) It's more consistent with the core, and future cluster, accessors.

  2) It ensures a sensible return type without explicit casts.

  3) It's generally preferable to use functions rather than macros.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17009/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Make use of the new change_*, set_* & clear_* accessor functions for CPS
(CM, CPC & GIC) registers where doing so makes the code easier to read
or shortens it without adversely affecting readability.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17005/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>