commit 99f2b130370b904ca5300079243fdbcafa2c708b upstream.

The SMAP register offsets in the versatile PCI controller code were
all off by four.  (This didn't have any observable bad effects
because on this board PHYS_OFFSET is zero, and (a) writing zero to
the flags register at offset 0x10 has no effect and (b) the reset
value of the SMAP register is zero anyway, so failing to write SMAP2
didn't matter.)

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 829f9fedee30cde2ec15e88d57ec11074db791e2 upstream.

The versatile PCI controller code was confused between the
PCI I/O window (at 0x43000000) and the first PCI memory
window (at 0x44000000). Pass the correct base address to
pci_remap_io() so that PCI I/O accesses work.

Since the first PCI memory window isn't used at all (it's
an odd size), rename the associated variables and labels
so that it's clear that it isn't related to the I/O window.

This has been tested and confirmed to fix PCI I/O accesses
both on physical PB926+PCI backplane hardware and on QEMU.

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f9b71fef12f0d6ac5c7051cfd87f7700f78c56b6 upstream.

The PCI controller code for the Versatile board has never had the
correct IRQ mapping for hardware.  For many years it had an odd
mapping ("all interrupts are int 27") which aligned with the
equivalent bug in QEMU.  However as of commit 1bc39ac5dab265
the mapping changed and no longer matched either hardware or QEMU,
with the result that any PCI card beyond the first in QEMU would
not have functioning interrupts; for example a boot with a SCSI
controller would time out as follows:

 ------------
 sym0: <895a> rev 0x0 at pci 0000:00:0d.0 irq 92
 sym0: SCSI BUS has been reset.
 scsi0 : sym-2.2.3
 [...]
 scsi 0:0:0:0: ABORT operation started
 scsi 0:0:0:0: ABORT operation timed-out.
 scsi 0:0:0:0: DEVICE RESET operation started
 scsi 0:0:0:0: DEVICE RESET operation timed-out.
 scsi 0:0:0:0: BUS RESET operation started
 scsi 0:0:0:0: BUS RESET operation timed-out.
 scsi 0:0:0:0: HOST RESET operation started
 sym0: SCSI BUS has been reset
 ------------

Fix the mapping so that it matches real hardware (checked against the
schematics for PB926 and backplane, and tested against the hardware).
This allows PCI cards using interrupts to work on hardware for the
first time; this change will also work with QEMU 1.5 or later, where
the equivalent bugs in the modelling of the hardware have been fixed.

Although QEMU will attempt to autodetect whether the kernel is
expecting the long-standing "everything is int 27" mapping or the one
hardware has, for certainty we force it into "definitely behave like
hardware mode"; this will avoid unexpected surprises later if we
implement sparse irqs. This is harmless on hardware.

Thanks to Paul Gortmaker for bisecting the problem and finding an initial
solution, to Russell King for providing the correct interrupt mapping,
and to Guenter Roeck for providing an initial version of this patch
and prodding me into relocating the hardware and retesting everything.

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 9dd4b2944c46e1fdbd0a516c221c8a2670cbf005 upstream.

xen_pm_init was unconditionally setting pm_power_off and arm_pm_restart
function pointers. This breaks multi-platform kernels. Make this
conditional on running as a Xen guest and make it a late_initcall to
ensure it is setup after platform code for Dom0.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull ARM SoC fixes from Olof Johansson:
 "Two straggling fixes that I had missed as they were posted a couple of
  weeks ago, causing problems with interrupts (breaking them completely)
  on the CSR SiRF platforms"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  arm: prima2: drop nr_irqs in mach as we moved to linear irqdomain
  irqchip: sirf: move from legacy mode to linear irqdomain

we don't need nr_irqs in machine any more after we move to
linear irqdomain for sirfsoc irqchip, so drop them.

Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Pull ARM fixes from Russell King:
 "This round of fixes is smaller than previous: a couple more updates
  for the security fixes, and a one-liner kexec fix"

* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
  ARM: 7816/1: CONFIG_KUSER_HELPERS: fix help text
  ARM: 7815/1: kexec: offline non panic CPUs on Kdump panic
  ARM: 7819/1: fiq: Cast the first argument of flush_icache_range()

Pull ARM SoC fixes from Olof Johansson:
 "A handful of fixes for 3.11 are still trickling in.  These are:
   - A couple of fixes for older OMAP platforms
   - Another few fixes for at91 (lateish due to European summer
     vacations)
   - A late-found problem with USB on Tegra, fix is to keep VBUS
     regulator on at all times
   - One fix for Exynos 5440 dealing with CPU detection
   - One MAINTAINERS update"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: tegra: always enable USB VBUS regulators
  ARM: davinci: nand: specify ecc strength
  ARM: OMAP: rx51: change musb mode to OTG
  ARM: OMAP2: fix musb usage for n8x0
  MAINTAINERS: Update email address for Benoit Cousson
  ARM: at91/DT: fix at91sam9n12ek memory node
  ARM: at91: add missing uart clocks DT entries
  ARM: SAMSUNG: fix to support for missing cpu specific map_io
  ARM: at91/DT: at91sam9x5ek: fix USB host property to enable port C

This fixes a regression exposed during the merge window by commit
9f310de "ARM: tegra: fix VBUS regulator GPIO polarity in DT"; namely that
USB VBUS doesn't get turned on, so USB devices are not detected. This
affects the internal USB port on TrimSlice (i.e. the USB->SATA bridge, to
which the SSD is connected) and the external port(s) on Seaboard/
Springbank and Whistler.

The Tegra DT as written in v3.11 allows two paths to enable USB VBUS:

1) Via the legacy DT binding for the USB controller; it can directly
   acquire a VBUS GPIO and activate it.

2) Via a regulator for VBUS, which is referenced by the new DT binding
   for the USB controller.

Those two methods both use the same GPIO, and hence whichever of the
USB controller and regulator gets probed first ends up owning the GPIO.
In practice, the USB driver only supports path (1) above, since the
patches to support the new USB binding are not present until v3.12:-(

In practice, the regulator ends up being probed first and owning the
GPIO. Since nothing enables the regulator (the USB driver code is not
yet present), the regulator ends up being turned off. This originally
caused no problem, because the polarity in the regulator definition was
incorrect, so attempting to turn off the regulator actually turned it
on, and everything worked:-(

However, when testing the new USB driver code in v3.12, I noticed the
incorrect polarity and fixed it in commit 9f310de "ARM: tegra: fix VBUS
regulator GPIO polarity in DT". In the context of v3.11, this patch then
caused the USB VBUS to actually turn off, which broke USB ports with VBUS
control. I got this patch included in v3.11-rc1 since it fixed a bug in
device tree (incorrect polarity specification), and hence was suitable to
be included early in the rc series. I evidently did not test the patch at
all, or correctly, in the context of v3.11, and hence did not notice the
issue that I have explained above:-(

Fix this by making the USB VBUS regulators always enabled. This way, if
the regulator owns the GPIO, it will always be turned on, even if there
is no USB driver code to request the regulator be turned on. Even
ignoring this bug, this is a reasonable way to configure the HW anyway.

If this patch is applied to v3.11, it will cause a couple pretty trivial
conflicts in tegra20-{trimslice,seaboard}.dts when creating v3.12, since
the context right above the added lines changed in patches destined for
v3.12.

Reported-by: Kyle McMartin <kmcmarti@redhat.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Pull Xen bug-fixes from Konrad Rzeszutek Wilk:
 - On ARM did not have balanced calls to get/put_cpu.
 - Fix to make tboot + Xen + Linux correctly.
 - Fix events VCPU binding issues.
 - Fix a vCPU online race where IPIs are sent to not-yet-online vCPU.

* tag 'stable/for-linus-3.11-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen/smp: initialize IPI vectors before marking CPU online
  xen/events: mask events when changing their VCPU binding
  xen/events: initialize local per-cpu mask for all possible events
  x86/xen: do not identity map UNUSABLE regions in the machine E820
  xen/arm: missing put_cpu in xen_percpu_init