Second Round of Renesas ARM Based SoC Fixes for v5.3

* RZ/G2M based HiHope main board
  - Re-enabled accidently disabled SDHI3 (eMMC) support

* tag 'renesas-fixes2-for-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  arm64: dts: renesas: hihope-common: Fix eMMC status

Link: https://lore.kernel.org/r/cover.1567675986.git.horms+renesas@verge.net.au
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Renesas ARM Based SoC Fixes for v5.3

* R-Car D3 (r8a77995) based Draak Board
  - Correct backlight regulator name in device tree

* tag 'renesas-fixes-for-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  arm64: dts: renesas: r8a77995: draak: Fix backlight regulator name

Signed-off-by: Arnd Bergmann <arnd@arndb.de>

SDHI3 got accidentally disabled while adding USB 2.0 support,
this patch fixes it.

Fixes: 734d277f412a ("arm64: dts: renesas: hihope-common: Add USB 2.0 support")
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: Amlogic fixes for v5.3-rc
- a few small DT fixes for g12a/g12b platforms

* tag 'amlogic-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
  arm64: dts: amlogic: odroid-n2: keep SD card regulator always on
  arm64: dts: meson-g12a-sei510: enable IR controller
  arm64: dts: meson-g12a: add missing dwc2 phy-names

Currently there are two nodes named "regulator1" in the Draak DTS: a
3.3V regulator for the eMMC and the LVDS decoder, and a 12V regulator
for the backlight.  This causes the former to be overwritten by the
latter.

Fix this by renaming all regulators with numerical suffixes to use named
suffixes, which are less likely to conflict.

Fixes: 4fbd4158fe8967e9 ("arm64: dts: renesas: r8a77995: draak: Add backlight")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

When powering off the Odroid N2, the tflash_vdd regulator is
automatically turned off by the kernel. This is a problem
when issuing the "reboot" command while using an SD card.
The boot ROM does not power this regulator back on, blocking
the reboot process at the boot ROM stage, preventing the
SD card from being detected.

Adding the "regulator-always-on" property fixes the problem.

Signed-off-by: Xavier Ruppen <xruppen@gmail.com>
Suggested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Fixes: c35f6dc5c377 ("arm64: dts: meson: Add minimal support for Odroid-N2")
[khilman: minor subject change: s/meson/amlogic/]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

Enable the IR receiver controller on the SEI510 board.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

The G12A USB2 OTG capable PHY uses a 8bit large UTMI bus, and the OTG
controller gets the PHY but width by probing the associated phy.

By default it will use 16bit wide settings if a phy is not specified,
in our case we specified the phy, but not the phy-names.

The dwc2 bindings specifies that if phys is present, phy-names shall be
"usb2-phy".

Adding phy-names = "usb2-phy" solves the OTG PHY bus configuration.

Fixes: 9baf7d6be730 ("arm64: dts: meson: g12a: Add G12A USB nodes")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

The i.MX8M SAI block is not compatible with the i.MX6SX one, as the
register layout has changed due to two version registers being added
at the beginning of the address map. Remove the bogus compatible.

Fixes: 8c61538dc945 ("arm64: dts: imx8mq: Add SAI2 node")
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

According to i.MX8MM reference manual Rev.1, 03/2019:

SAI3_RXC pin's mux option #1 should be GPT1_CLK, NOT GPT1_CAPTURE2;
SAI3_TXFS pin's mux option #1 should be GPT1_CAPTURE2, NOT GPT1_CLK.

Fixes: c1c9d41319c3 ("dt-bindings: imx: Add pinctrl binding doc for imx8mm")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>