[ Upstream commit 9b55613f42e8d40d5c9ccb8970bde6af4764b2ab ]

When a kernel is built covering ARMv6 to ARMv7, we omit to clear the
IT state when entering a signal handler.  This can cause the first
few instructions to be conditionally executed depending on the parent
context.

In any case, the original test for >= ARMv7 is broken - ARMv6 can have
Thumb-2 support as well, and an ARMv6T2 specific build would omit this
code too.

Relax the test back to ARMv6 or greater.  This results in us always
clearing the IT state bits in the PSR, even on CPUs where these bits
are reserved.  However, they're reserved for the IT state, so this
should cause no harm.

Cc: <stable@vger.kernel.org>
Fixes: d71e1352e240 ("Clear the IT state when invoking a Thumb-2 signal handler")
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: H. Nikolaus Schaller <hns@goldelico.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

Two files that get included when building the multi_v7_defconfig target
fail to build when selecting THUMB2_KERNEL for this configuration.

In both cases, we can just build the file as ARM code, as none of its
symbols are exported to modules, so there are no interworking concerns.
In the iwmmxt.S case, add ENDPROC() declarations so the symbols are
annotated as functions, resulting in the linker to emit the appropriate
mode switches.

Acked-by: Nicolas Pitre <nico@linaro.org>
Tested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
(cherry picked from commit 13d1b9575ac2c2da143cd2236b6cf0fc314570f8)
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 1b97937246d8b97c0760d16d8992c7937bdf5e6a ]

Josh Stone reports:

  I've discovered a case where both arm and arm64 will miss a ptrace
  syscall-exit that they should report.  If the syscall is entered
  without TIF_SYSCALL_TRACE set, then it goes on the fast path.  It's
  then possible to have TIF_SYSCALL_TRACE added in the middle of the
  syscall, but ret_fast_syscall doesn't check this flag again.

Fix this by always checking for a syscall trace in the fast exit path.

Reported-by: Josh Stone <jistone@redhat.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit c097877319ab61dd045b6497953b4e3df8f2bb44 ]

arm64 builds with GCC 5 have caused the __asmeq assertions in the PSCI
calling code to fire, so move the ARM PSCI calls out of line into their
own assembly file for consistency and to safeguard against the same
issue occuring with the 32-bit toolchain.

[will: brought into line with arm64 implementation]

Reported-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

[ Upstream commit 767bf7e7a1e82a81c59778348d156993d0a6175d ]

Normally, when a CPU wants to clear a cache line to zero in the external
L2 cache, it would generate bus cycles to write each word as it would do
with any other data access.

However, a Cortex A9 connected to a L2C-310 has a specific feature where
the CPU can detect this operation, and signal that it wants to zero an
entire cache line.  This feature, known as Full Line of Zeros (FLZ),
involves a non-standard AXI signalling mechanism which only the L2C-310
can properly interpret.

There are separate enable bits in both the L2C-310 and the Cortex A9 -
the L2C-310 needs to be enabled and have the FLZ enable bit set in the
auxiliary control register before the Cortex A9 has this feature
enabled.

Unfortunately, the suspend code was not respecting this - it's not
obvious from the code:

swsusp_arch_suspend()
 cpu_suspend() /* saves the Cortex A9 auxiliary control register */
  arch_save_image()
  soft_restart() /* turns off FLZ in Cortex A9, and disables L2C */
   cpu_resume() /* restores the Cortex A9 registers, inc auxcr */

At this point, we end up with the L2C disabled, but the Cortex A9 with
FLZ enabled - which means any memset() or zeroing of a full cache line
will fail to take effect.

A similar issue exists in the resume path, but it's slightly more
complex:

swsusp_arch_suspend()
 cpu_suspend() /* saves the Cortex A9 auxiliary control register */
  arch_save_image() /* image with A9 auxcr saved */
...
swsusp_arch_resume()
 call_with_stack()
  arch_restore_image() /* restores image with A9 auxcr saved above */
  soft_restart() /* turns off FLZ in Cortex A9, and disables L2C */
   cpu_resume() /* restores the Cortex A9 registers, inc auxcr */

Again, here we end up with the L2C disabled, but Cortex A9 FLZ enabled.

There's no need to turn off the L2C in either of these two paths; there
are benefits from not doing so - for example, the page copies will be
faster with the L2C enabled.

Hence, fix this by providing a variant of soft_restart() which can be
used without turning the L2 cache controller off, and use it in both
of these paths to keep the L2C enabled across the respective resume
transitions.

Fixes: 8ef418c7178f ("ARM: l2c: trial at enabling some Cortex-A9 optimisations")
Reported-by: Sean Cross <xobs@kosagi.com>
Tested-by: Sean Cross <xobs@kosagi.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>

commit 4bf9636c39ac70da091d5a2e28d3448eaa7f115c upstream.

Commit 9fc2105aeaaf ("ARM: 7830/1: delay: don't bother reporting
bogomips in /proc/cpuinfo") breaks audio in python, and probably
elsewhere, with message

  FATAL: cannot locate cpu MHz in /proc/cpuinfo

I'm not the first one to hit it, see for example

  https://theredblacktree.wordpress.com/2014/08/10/fatal-cannot-locate-cpu-mhz-in-proccpuinfo/
  https://devtalk.nvidia.com/default/topic/765800/workaround-for-fatal-cannot-locate-cpu-mhz-in-proc-cpuinf/?offset=1

Reading original changelog, I have to say "Stop breaking working setups.
You know who you are!".

Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull ARM fixes from Russell King:
 "Another round of relatively small ARM fixes.

  Thomas spotted that the strex backoff delay bit was a disable bit, so
  it needed to be clear for this to work.  Vladimir spotted that using a
  restart block for the cache flush operation would return -EINTR, which
  userspace was not expecting.  Dmitry spotted that the auxiliary
  control register accesses for Xscale were not correct"

* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  ARM: 8226/1: cacheflush: get rid of restarting block
  ARM: 8222/1: mvebu: enable strex backoff delay
  ARM: 8216/1: xscale: correct auxiliary register in suspend/resume

We cannot restart cacheflush safely if a process provides user-defined
signal handler and signal is pending. In this case -EINTR is returned
and it is expected that process re-invokes syscall. However, there are
a few problems with that:
 * looks like nobody bothers checking return value from cacheflush
 * but if it did, we don't provide the restart address for that, so the
   process has to use the same range again
 * ...and again, what might lead to looping forever

So, remove cacheflush restarting code and terminate cache flushing
as early as fatal signal is pending.

Cc: stable@vger.kernel.org # 3.12+
Reported-by: Chanho Min <chanho.min@lge.com>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Pull ARM fixes from Russell King:
 - add the new bpf syscall to ARM.
 - drop a redundant return statement in __iommu_alloc_remap()
 - fix a performance issue noticed by Thomas Petazzoni with
   kmap_atomic().
 - fix an issue with the L2 cache OF parsing code which caused it to
   incorrectly print warnings on each boot, and make the warning text
   more consistent with the rest of the code

* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  ARM: 8180/1: mm: implement no-highmem fast path in kmap_atomic_pfn()
  ARM: 8183/1: l2c: Improve l2c310_of_parse() error message
  ARM: 8181/1: Drop extra return statement
  ARM: 8182/1: l2c: Make l2x0_cache_size_of_parse() return 'int'
  ARM: enable bpf syscall

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>