commit 767bf7e7a1e82a81c59778348d156993d0a6175d upstream.

Normally, when a CPU wants to clear a cache line to zero in the external
L2 cache, it would generate bus cycles to write each word as it would do
with any other data access.

However, a Cortex A9 connected to a L2C-310 has a specific feature where
the CPU can detect this operation, and signal that it wants to zero an
entire cache line.  This feature, known as Full Line of Zeros (FLZ),
involves a non-standard AXI signalling mechanism which only the L2C-310
can properly interpret.

There are separate enable bits in both the L2C-310 and the Cortex A9 -
the L2C-310 needs to be enabled and have the FLZ enable bit set in the
auxiliary control register before the Cortex A9 has this feature
enabled.

Unfortunately, the suspend code was not respecting this - it's not
obvious from the code:

swsusp_arch_suspend()
 cpu_suspend() /* saves the Cortex A9 auxiliary control register */
  arch_save_image()
  soft_restart() /* turns off FLZ in Cortex A9, and disables L2C */
   cpu_resume() /* restores the Cortex A9 registers, inc auxcr */

At this point, we end up with the L2C disabled, but the Cortex A9 with
FLZ enabled - which means any memset() or zeroing of a full cache line
will fail to take effect.

A similar issue exists in the resume path, but it's slightly more
complex:

swsusp_arch_suspend()
 cpu_suspend() /* saves the Cortex A9 auxiliary control register */
  arch_save_image() /* image with A9 auxcr saved */
...
swsusp_arch_resume()
 call_with_stack()
  arch_restore_image() /* restores image with A9 auxcr saved above */
  soft_restart() /* turns off FLZ in Cortex A9, and disables L2C */
   cpu_resume() /* restores the Cortex A9 registers, inc auxcr */

Again, here we end up with the L2C disabled, but Cortex A9 FLZ enabled.

There's no need to turn off the L2C in either of these two paths; there
are benefits from not doing so - for example, the page copies will be
faster with the L2C enabled.

Hence, fix this by providing a variant of soft_restart() which can be
used without turning the L2 cache controller off, and use it in both
of these paths to keep the L2C enabled across the respective resume
transitions.

Fixes: 8ef418c7178f ("ARM: l2c: trial at enabling some Cortex-A9 optimisations")
Reported-by: Sean Cross <xobs@kosagi.com>
Tested-by: Sean Cross <xobs@kosagi.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

If the kernel is running in hypervisor mode or monitor mode we'll
print UK6_32 or UK10_32 if we call into __show_regs(). Let's
update these strings to indicate the new modes that didn't exist
when this code was written.

Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Pull restart handler infrastructure from Guenter Roeck:
 "This series was supposed to be pulled through various trees using it,
  and I did not plan to send a separate pull request.  As it turns out,
  the pinctrl tree did not merge with it, is now upstream, and uses it,
  meaning there are now build failures.

  Please pull this series directly to fix those build failures"

* tag 'restart-handler-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  arm/arm64: unexport restart handlers
  watchdog: sunxi: register restart handler with kernel restart handler
  watchdog: alim7101: register restart handler with kernel restart handler
  watchdog: moxart: register restart handler with kernel restart handler
  arm: support restart through restart handler call chain
  arm64: support restart through restart handler call chain
  power/restart: call machine_restart instead of arm_pm_restart
  kernel: add support for kernel restart handler call chain

The sigpage is currently placed alongside shared libraries etc in the
address space.  Similar to what x86_64 does for its VDSO, place the
sigpage at a randomized offset above the stack so that learning the
base address of the sigpage doesn't help expose where shared libraries
are loaded in the address space (and vice versa).

Signed-off-by: Nathan Lynch <nathan_lynch@mentor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

_install_special_mapping allows the VMA to be identifed in
/proc/pid/maps without the use of arch_vma_name, providing a
slight net reduction in object size:

  text    data     bss     dec     hex filename
  2996      96     144    3236     ca4 arch/arm/kernel/process.o (before)
  2956     104     144    3204     c84 arch/arm/kernel/process.o (after)

Signed-off-by: Nathan Lynch <nathan_lynch@mentor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Implementing a restart handler in a module don't make sense as there would
be no guarantee that the module is loaded when a restart is needed.
Unexport arm_pm_restart to ensure that no one gets the idea to do it
anyway.

Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

The kernel core now supports a restart handler call chain for system
restart functions.

With this change, the arm_pm_restart callback is now optional, so drop its
initialization and check if it is set before calling it.  Only call the
kernel restart handler if arm_pm_restart is not set.

Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

Remove an unnecessary newline in show_regs().

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The TPIDRURO and TPIDRURW registers need to be flushed during exec;
otherwise TLS information is potentially leaked.  TPIDRURO in
particular needs careful treatment.  Since flush_thread basically
needs the same code used to set the TLS in arm_syscall, pull that into
a common set_tls helper in tls.h and use it in both places.

Similarly, TEEHBR needs to be cleared during exec as well.  Clearing
its save slot in thread_info isn't right as there is no guarantee
that a thread switch will occur before the new program runs.  Just
setting the register directly is sufficient.

Signed-off-by: Nathan Lynch <nathan_lynch@mentor.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>