Since commit 6ce0d2001692 ("ARM: dma: Use dma_pfn_offset for dma address translation"),
dma_to_pfn() already returns the PFN with the physical memory start offset
so we don't need to add it again.

This fixes USB mass storage lock-up problem on systems that can't do DMA
over the entire physical memory range (e.g.) Keystone 2 systems with 4GB RAM
can only do DMA over the first 2GB. [K2E-EVM].

What happens there is that without this patch SCSI layer sets a wrong
bounce buffer limit in scsi_calculate_bounce_limit() for the USB mass
storage device. dma_max_pfn() evaluates to 0x8fffff and bounce_limit
is set to 0x8fffff000 whereas maximum DMA'ble physical memory on Keystone 2
is 0x87fffffff. This results in non DMA'ble pages being given to the
USB controller and hence the lock-up.

NOTE: in the above case, USB-SCSI-device's dma_pfn_offset was showing as 0.
This should have really been 0x780000 as on K2e, LOWMEM_START is 0x80000000
and HIGHMEM_START is 0x800000000. DMA zone is 2GB so dma_max_pfn should be
0x87ffff. The incorrect dma_pfn_offset for the USB storage device is because
USB devices are not correctly inheriting the dma_pfn_offset from the
USB host controller. This will be fixed by a separate patch.

Fixes: 6ce0d2001692 ("ARM: dma: Use dma_pfn_offset for dma address translation")
Cc: stable@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The cachepolicy variable gets initialized using a masked pmd
value. So far, the pmd has been masked with flags valid for the
2-page table format, but the 3-page table format requires a
different mask. On LPAE, this lead to a wrong assumption of what
initial cache policy has been used. Later a check forces the
cache policy to writealloc and prints the following warning:
Forcing write-allocate cache policy for SMP

This patch introduces a new definition PMD_SECT_CACHE_MASK for
both page table formats which masks in all cache flags in both
cases.

Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Pull usercopy protection from Kees Cook:
 "Tbhis implements HARDENED_USERCOPY verification of copy_to_user and
  copy_from_user bounds checking for most architectures on SLAB and
  SLUB"

* tag 'usercopy-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  mm: SLUB hardened usercopy support
  mm: SLAB hardened usercopy support
  s390/uaccess: Enable hardened usercopy
  sparc/uaccess: Enable hardened usercopy
  powerpc/uaccess: Enable hardened usercopy
  ia64/uaccess: Enable hardened usercopy
  arm64/uaccess: Enable hardened usercopy
  ARM: uaccess: Enable hardened usercopy
  x86/uaccess: Enable hardened usercopy
  mm: Hardened usercopy
  mm: Implement stack frame object validation
  mm: Add is_migrate_cma_page

The dma-mapping core and the implementations do not change the DMA
attributes passed by pointer.  Thus the pointer can point to const data.
However the attributes do not have to be a bitfield.  Instead unsigned
long will do fine:

1. This is just simpler.  Both in terms of reading the code and setting
   attributes.  Instead of initializing local attributes on the stack
   and passing pointer to it to dma_set_attr(), just set the bits.

2. It brings safeness and checking for const correctness because the
   attributes are passed by value.

Semantic patches for this change (at least most of them):

    virtual patch
    virtual context

    @r@
    identifier f, attrs;

    @@
    f(...,
    - struct dma_attrs *attrs
    + unsigned long attrs
    , ...)
    {
    ...
    }

    @@
    identifier r.f;
    @@
    f(...,
    - NULL
    + 0
     )

and

    // Options: --all-includes
    virtual patch
    virtual context

    @r@
    identifier f, attrs;
    type t;

    @@
    t f(..., struct dma_attrs *attrs);

    @@
    identifier r.f;
    @@
    f(...,
    - NULL
    + 0
     )

Link: http://lkml.kernel.org/r/1468399300-5399-2-git-send-email-k.kozlowski@samsung.com
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Acked-by: Mark Salter <msalter@redhat.com> [c6x]
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com> [cris]
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> [drm]
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Joerg Roedel <jroedel@suse.de> [iommu]
Acked-by: Fabien Dessenne <fabien.dessenne@st.com> [bdisp]
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com> [vb2-core]
Acked-by: David Vrabel <david.vrabel@citrix.com> [xen]
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> [xen swiotlb]
Acked-by: Joerg Roedel <jroedel@suse.de> [iommu]
Acked-by: Richard Kuo <rkuo@codeaurora.org> [hexagon]
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Acked-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> [s390]
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no> [avr32]
Acked-by: Vineet Gupta <vgupta@synopsys.com> [arc]
Acked-by: Robin Murphy <robin.murphy@arm.com> [arm64 and dma-iommu]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge yet more updates from Andrew Morton:

 - the rest of ocfs2

 - various hotfixes, mainly MM

 - quite a bit of misc stuff - drivers, fork, exec, signals, etc.

 - printk updates

 - firmware

 - checkpatch

 - nilfs2

 - more kexec stuff than usual

 - rapidio updates

 - w1 things

* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (111 commits)
  ipc: delete "nr_ipc_ns"
  kcov: allow more fine-grained coverage instrumentation
  init/Kconfig: add clarification for out-of-tree modules
  config: add android config fragments
  init/Kconfig: ban CONFIG_LOCALVERSION_AUTO with allmodconfig
  relay: add global mode support for buffer-only channels
  init: allow blacklisting of module_init functions
  w1:omap_hdq: fix regression
  w1: add helper macro module_w1_family
  w1: remove need for ida and use PLATFORM_DEVID_AUTO
  rapidio/switches: add driver for IDT gen3 switches
  powerpc/fsl_rio: apply changes for RIO spec rev 3
  rapidio: modify for rev.3 specification changes
  rapidio: change inbound window size type to u64
  rapidio/idt_gen2: fix locking warning
  rapidio: fix error handling in mbox request/release functions
  rapidio/tsi721_dma: advance queue processing from transfer submit call
  rapidio/tsi721: add messaging mbox selector parameter
  rapidio/tsi721: add PCIe MRRS override parameter
  rapidio/tsi721_dma: add channel mask and queue size parameters
  ...

Provide kexec with the boot view of memory by overriding the normal
kexec translation functions added in a previous patch.  We also need to
fix a call to memblock in machine_kexec_prepare() so that we provide it
with a running-view physical address rather than a boot- view physical
address.

Link: http://lkml.kernel.org/r/E1b8koa-0004Hl-Ey@rmk-PC.armlinux.org.uk
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Pratyush Anand <panand@redhat.com>
Cc: Vitaly Andrianov <vitalya@ti.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Simon Horman <horms@verge.net.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull PCI updates from Bjorn Helgaas:
 "Highlights:

   - ARM64 support for ACPI host bridges

   - new drivers for Axis ARTPEC-6 and Marvell Aardvark

   - new pci_alloc_irq_vectors() interface for MSI-X, MSI, legacy INTx

   - pci_resource_to_user() cleanup (more to come)

  Detailed summary:

  Enumeration:
   - Move ecam.h to linux/include/pci-ecam.h (Jayachandran C)
   - Add parent device field to ECAM struct pci_config_window (Jayachandran C)
   - Add generic MCFG table handling (Tomasz Nowicki)
   - Refactor pci_bus_assign_domain_nr() for CONFIG_PCI_DOMAINS_GENERIC (Tomasz Nowicki)
   - Factor DT-specific pci_bus_find_domain_nr() code out (Tomasz Nowicki)

  Resource management:
   - Add devm_request_pci_bus_resources() (Bjorn Helgaas)
   - Unify pci_resource_to_user() declarations (Bjorn Helgaas)
   - Implement pci_resource_to_user() with pcibios_resource_to_bus() (microblaze, powerpc, sparc) (Bjorn Helgaas)
   - Request host bridge window resources (designware, iproc, rcar, xgene, xilinx, xilinx-nwl) (Bjorn Helgaas)
   - Make PCI I/O space optional on ARM32 (Bjorn Helgaas)
   - Ignore write combining when mapping I/O port space (Bjorn Helgaas)
   - Claim bus resources on MIPS PCI_PROBE_ONLY set-ups (Bjorn Helgaas)
   - Remove unicore32 pci=firmware command line parameter handling (Bjorn Helgaas)
   - Support I/O resources when parsing host bridge resources (Jayachandran C)
   - Add helpers to request/release memory and I/O regions (Johannes Thumshirn)
   - Use pci_(request|release)_mem_regions (NVMe, lpfc, GenWQE, ethernet/intel, alx) (Johannes Thumshirn)
   - Extend pci=resource_alignment to specify device/vendor IDs (Koehrer Mathias (ETAS/ESW5))
   - Add generic pci_bus_claim_resources() (Lorenzo Pieralisi)
   - Claim bus resources on ARM32 PCI_PROBE_ONLY set-ups (Lorenzo Pieralisi)
   - Remove ARM32 and ARM64 arch-specific pcibios_enable_device() (Lorenzo Pieralisi)
   - Add pci_unmap_iospace() to unmap I/O resources (Sinan Kaya)
   - Remove powerpc __pci_mmap_set_pgprot() (Yinghai Lu)

  PCI device hotplug:
   - Allow additional bus numbers for hotplug bridges (Keith Busch)
   - Ignore interrupts during D3cold (Lukas Wunner)

  Power management:
   - Enforce type casting for pci_power_t (Andy Shevchenko)
   - Don't clear d3cold_allowed for PCIe ports (Mika Westerberg)
   - Put PCIe ports into D3 during suspend (Mika Westerberg)
   - Power on bridges before scanning new devices (Mika Westerberg)
   - Runtime resume bridge before rescan (Mika Westerberg)
   - Add runtime PM support for PCIe ports (Mika Westerberg)
   - Remove redundant check of pcie_set_clkpm (Shawn Lin)

  Virtualization:
   - Add function 1 DMA alias quirk for Marvell 88SE9182 (Aaron Sierra)
   - Add DMA alias quirk for Adaptec 3805 (Alex Williamson)
   - Mark Atheros AR9485 and QCA9882 to avoid bus reset (Chris Blake)
   - Add ACS quirk for Solarflare SFC9220 (Edward Cree)

  MSI:
   - Fix PCI_MSI dependencies (Arnd Bergmann)
   - Add pci_msix_desc_addr() helper (Christoph Hellwig)
   - Switch msix_program_entries() to use pci_msix_desc_addr() (Christoph Hellwig)
   - Make the "entries" argument to pci_enable_msix() optional (Christoph Hellwig)
   - Provide sensible IRQ vector alloc/free routines (Christoph Hellwig)
   - Spread interrupt vectors in pci_alloc_irq_vectors() (Christoph Hellwig)

  Error Handling:
   - Bind DPC to Root Ports as well as Downstream Ports (Keith Busch)
   - Remove DPC tristate module option (Keith Busch)
   - Convert Downstream Port Containment driver to use devm_* functions (Mika Westerberg)

  Generic host bridge driver:
   - Select IRQ_DOMAIN (Arnd Bergmann)
   - Claim bus resources on PCI_PROBE_ONLY set-ups (Lorenzo Pieralisi)

  ACPI host bridge driver:
   - Add ARM64 acpi_pci_bus_find_domain_nr() (Tomasz Nowicki)
   - Add ARM64 ACPI support for legacy IRQs parsing and consolidation with DT code (Tomasz Nowicki)
   - Implement ARM64 AML accessors for PCI_Config region (Tomasz Nowicki)
   - Support ARM64 ACPI-based PCI host controller (Tomasz Nowicki)

  Altera host bridge driver:
   - Check link status before retrain link (Ley Foon Tan)
   - Poll for link up status after retraining the link (Ley Foon Tan)

  Axis ARTPEC-6 host bridge driver:
   - Add PCI_MSI_IRQ_DOMAIN dependency (Arnd Bergmann)
   - Add DT binding for Axis ARTPEC-6 PCIe controller (Niklas Cassel)
   - Add Axis ARTPEC-6 PCIe controller driver (Niklas Cassel)

  Intel VMD host bridge driver:
   - Use lock save/restore in interrupt enable path (Jon Derrick)
   - Select device dma ops to override (Keith Busch)
   - Initialize list item in IRQ disable (Keith Busch)
   - Use x86_vector_domain as parent domain (Keith Busch)
   - Separate MSI and MSI-X vector sharing (Keith Busch)

  Marvell Aardvark host bridge driver:
   - Add DT binding for the Aardvark PCIe controller (Thomas Petazzoni)
   - Add Aardvark PCI host controller driver (Thomas Petazzoni)
   - Add Aardvark PCIe support for Armada 3700 (Thomas Petazzoni)

  Microsoft Hyper-V host bridge driver:
   - Fix interrupt cleanup path (Cathy Avery)
   - Don't leak buffer in hv_pci_onchannelcallback() (Vitaly Kuznetsov)
   - Handle all pending messages in hv_pci_onchannelcallback() (Vitaly Kuznetsov)

  NVIDIA Tegra host bridge driver:
   - Program PADS_REFCLK_CFG* always, not just on legacy SoCs (Stephen Warren)
   - Program PADS_REFCLK_CFG* registers with per-SoC values (Stephen Warren)
   - Use lower-case hex consistently for register definitions (Thierry Reding)
   - Use generic pci_remap_iospace() rather than ARM32-specific one (Thierry Reding)
   - Stop setting pcibios_min_mem (Thierry Reding)

  Renesas R-Car host bridge driver:
   - Drop gen2 dummy I/O port region (Bjorn Helgaas)

  TI DRA7xx host bridge driver:
   - Fix return value in case of error (Christophe JAILLET)

  Xilinx AXI host bridge driver:
   - Fix return value in case of error (Christophe JAILLET)

  Miscellaneous:
   - Make bus_attr_resource_alignment static (Ben Dooks)
   - Include <asm/dma.h> for isa_dma_bridge_buggy (Ben Dooks)
   - MAINTAINERS: Add file patterns for PCI device tree bindings (Geert Uytterhoeven)
   - Make host bridge drivers explicitly non-modular (Paul Gortmaker)"

* tag 'pci-v4.8-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (125 commits)
  PCI: xgene: Make explicitly non-modular
  PCI: thunder-pem: Make explicitly non-modular
  PCI: thunder-ecam: Make explicitly non-modular
  PCI: tegra: Make explicitly non-modular
  PCI: rcar-gen2: Make explicitly non-modular
  PCI: rcar: Make explicitly non-modular
  PCI: mvebu: Make explicitly non-modular
  PCI: layerscape: Make explicitly non-modular
  PCI: keystone: Make explicitly non-modular
  PCI: hisi: Make explicitly non-modular
  PCI: generic: Make explicitly non-modular
  PCI: designware-plat: Make it explicitly non-modular
  PCI: artpec6: Make explicitly non-modular
  PCI: armada8k: Make explicitly non-modular
  PCI: artpec: Add PCI_MSI_IRQ_DOMAIN dependency
  PCI: Add ACS quirk for Solarflare SFC9220
  arm64: dts: marvell: Add Aardvark PCIe support for Armada 3700
  PCI: aardvark: Add Aardvark PCI host controller driver
  dt-bindings: add DT binding for the Aardvark PCIe controller
  PCI: tegra: Program PADS_REFCLK_CFG* registers with per-SoC values
  ...

Pull KVM updates from Paolo Bonzini:

 - ARM: GICv3 ITS emulation and various fixes.  Removal of the
   old VGIC implementation.

 - s390: support for trapping software breakpoints, nested
   virtualization (vSIE), the STHYI opcode, initial extensions
   for CPU model support.

 - MIPS: support for MIPS64 hosts (32-bit guests only) and lots
   of cleanups, preliminary to this and the upcoming support for
   hardware virtualization extensions.

 - x86: support for execute-only mappings in nested EPT; reduced
   vmexit latency for TSC deadline timer (by about 30%) on Intel
   hosts; support for more than 255 vCPUs.

 - PPC: bugfixes.

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (302 commits)
  KVM: PPC: Introduce KVM_CAP_PPC_HTM
  MIPS: Select HAVE_KVM for MIPS64_R{2,6}
  MIPS: KVM: Reset CP0_PageMask during host TLB flush
  MIPS: KVM: Fix ptr->int cast via KVM_GUEST_KSEGX()
  MIPS: KVM: Sign extend MFC0/RDHWR results
  MIPS: KVM: Fix 64-bit big endian dynamic translation
  MIPS: KVM: Fail if ebase doesn't fit in CP0_EBase
  MIPS: KVM: Use 64-bit CP0_EBase when appropriate
  MIPS: KVM: Set CP0_Status.KX on MIPS64
  MIPS: KVM: Make entry code MIPS64 friendly
  MIPS: KVM: Use kmap instead of CKSEG0ADDR()
  MIPS: KVM: Use virt_to_phys() to get commpage PFN
  MIPS: Fix definition of KSEGX() for 64-bit
  KVM: VMX: Add VMCS to CPU's loaded VMCSs before VMPTRLD
  kvm: x86: nVMX: maintain internal copy of current VMCS
  KVM: PPC: Book3S HV: Save/restore TM state in H_CEDE
  KVM: PPC: Book3S HV: Pull out TM state save/restore into separate procedures
  KVM: arm64: vgic-its: Simplify MAPI error handling
  KVM: arm64: vgic-its: Make vgic_its_cmd_handle_mapi similar to other handlers
  KVM: arm64: vgic-its: Turn device_id validation into generic ID validation
  ...

Pull ARM SoC platform updates from Olof Johansson:
 "Improved and new platform support for various SoCs:

  New SoC support:
   - Broadcom BCM23550
   - Freescale i.MX7Solo
   - Qualcomm MDM9615
   - Renesas r8a7792

  Improvements:
   - convert clps711x to multiplatform
   - debug uart improvements for Atmel platforms
   - Tango platform improvements: HOTPLUG_CPU, Suspend-to-ram
   - OMAP tweaks and improvements to hwmod
   - OMAP support for kexec on SMP"

* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (109 commits)
  ARM: davinci: fix build break because of undeclared dm365_evm_snd_data
  ARM: s3c64xx: smartq: Avoid sparse warnings
  ARM: sti: Implement dummy L2 cache's write_sec
  ARM: STi: Update machine _namestr to be more generic.
  arm: meson: explicitly select clk drivers
  ARM: tango: add Suspend-to-RAM support
  ARM: hisi: consolidate the hisilicon machine entries
  ARM: tango: fix CONFIG_HOTPLUG_CPU=n build
  MAINTAINERS: Update BCM281XX/BCM11XXX/BCM216XX entry
  MAINTAINERS: Update BCM63XX entry
  MAINTAINERS: Add NS2 entry
  MAINTAINERS: Fix nsp false-positives
  MAINTAINERS: Change L to M for Broadcom ARM/ARM64 SoC entries
  ARM: debug: Enable DEBUG_BCM_5301X for Northstar Plus SoCs
  ARM: clps711x: Switch to MULTIPLATFORM
  ARM: clps711x: Remove boards support
  ARM: clps711x: Add basic DT support
  ARM: clps711x: Reduce static map size
  ARM: SAMSUNG: Constify iomem address passed to s5p_init_cpu
  ARM: oxnas: Change OX810SE default driver config
  ...

Conflicts:
	drivers/nvme/host/pci.c