Pull ARM SoC late cleanups from Arnd Bergmann:
 "These could not be part of the first cleanup branch, because they
  either came too late in the cycle, or they have dependencies on other
  branches.  Important changes are:

   - The integrator platform is almost multiplatform capable after some
     reorganization (Linus Walleij)
   - Minor cleanups on Zynq (Michal Simek)
   - Lots of changes for Exynos and other Samsung platforms, including
     further preparations for multiplatform support and the clocks
     bindings are rearranged"

* tag 'tags/cleanup2-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
  devicetree: fix newly added exynos sata bindings
  ARM: EXYNOS: Fix compilation error in cpuidle.c
  ARM: S5P64X0: Explicitly include linux/serial_s3c.h in mach/pm-core.h
  ARM: EXYNOS: Remove hardware.h file
  ARM: SAMSUNG: Remove hardware.h inclusion
  ARM: S3C24XX: Remove invalid code from hardware.h
  dt-bindings: clock: Move exynos-audss-clk.h to dt-bindings/clock
  ARM: dts: Keep some essential LDOs enabled for arndale-octa board
  ARM: dts: Disable MDMA1 node for arndale-octa board
  ARM: S3C64XX: Fix build for implicit serial_s3c.h inclusion
  serial: s3c: Fix build of header without serial_core.h preinclusion
  ARM: EXYNOS: Allow wake-up using GIC interrupts
  ARM: EXYNOS: Stop using legacy Samsung PM code
  ARM: EXYNOS: Remove PM initcalls and useless indirection
  ARM: EXYNOS: Fix abuse of CONFIG_PM
  ARM: SAMSUNG: Move s3c_pm_check_* prototypes to plat/pm-common.h
  ARM: SAMSUNG: Move common save/restore helpers to separate file
  ARM: SAMSUNG: Move Samsung PM debug code into separate file
  ARM: SAMSUNG: Consolidate PM debug functions
  ARM: SAMSUNG: Use debug_ll_addr() to get UART base address
  ...

Pull ARM SoC cleanups from Arnd Bergmann:
 "These cleanup patches are mainly move stuff around and should all be
  harmless.  They are mainly split out so that other branches can be
  based on top to avoid conflicts.

  Notable changes are:

   - We finally remove all mach/timex.h, after CLOCK_TICK_RATE is no
     longer used (Uwe Kleine-König)
   - The Qualcomm MSM platform is split out into legacy mach-msm and
     new-style mach-qcom, to allow easier maintainance of the new
     hardware support without regressions (Kumar Gala)
   - A rework of some of the Kconfig logic to simplify multiplatform
     support (Rob Herring)
   - Samsung Exynos gets closer to supporting multiplatform (Sachin
     Kamat and others)
   - mach-bcm3528 gets merged into mach-bcm (Stephen Warren)
   - at91 gains some common clock framework support (Alexandre Belloni,
     Jean-Jacques Hiblot and other French people)"

* tag 'cleanup-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (89 commits)
  ARM: hisi: select HAVE_ARM_SCU only for SMP
  ARM: efm32: allow uncompress debug output
  ARM: prima2: build reset code standalone
  ARM: at91: add PWM clock
  ARM: at91: move sam9261 SoC to common clk
  ARM: at91: prepare common clk transition for sam9261 SoC
  ARM: at91: updated the at91_dt_defconfig with support for the ADS7846
  ARM: at91: dt: sam9261: Device Tree support for the at91sam9261ek
  ARM: at91: dt: defconfig: Added the sam9261 to the list of DT-enabled SOCs
  ARM: at91: dt: Add at91sam9261 dt SoC support
  ARM: at91: switch sam9rl to common clock framework
  ARM: at91/dt: define main clk frequency of at91sam9rlek
  ARM: at91/dt: define at91sam9rl clocks
  ARM: at91: prepare common clk transition for sam9rl SoCs
  ARM: at91: prepare sam9 dt boards transition to common clk
  ARM: at91: dt: sam9rl: Device Tree for the at91sam9rlek
  ARM: at91/defconfig: Add the sam9rl to the list of DT-enabled SOCs
  ARM: at91: Add at91sam9rl DT SoC support
  ARM: at91: prepare at91sam9rl DT transition
  ARM: at91/defconfig: refresh at91sam9260_9g20_defconfig
  ...

These are dependencies for the following Samsung branches

Signed-off-by: Arnd Bergmann <arnd@arndb.de>

In a combined ARMv6/v7 kernel, we cannot use the
movt/movw instructions to load an immediate, as they
are not valid on ARMv6.

This changes the file to use an indirect load instead,
as lots of other implementations do.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-tegra@vger.kernel.org

Add missing waituart implementation.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

regs-serial.h only includes linux/serial_s3c.h. Include this
header directly in samsung.S to remove unnecessary platform
dependency.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

From Shawn Guo:
i.MX SoC changes for 3.14:
 - Add the initial i.MX50 SoC support
 - Support device tree boot for i.MX35
 - Move imx5 clock driver to use macros for clock ID
 - Some random updates and non-critical fixes on clock drivers
 - A few defconfig updates and minor cleanups

* tag 'imx-soc-3.14' of git://git.linaro.org/people/shawnguo/linux-2.6: (37 commits)
  ARM: imx: improve the comment of CCM lpm SW workaround
  ARM: imx: improve status check of clock gate
  ARM: imx: add necessary interface for pfd
  ARM: imx_v6_v7_defconfig: Select CONFIG_REGULATOR_PFUZE100
  ARM: imx_v6_v7_defconfig: Select MX35 and MX50 device tree support
  ARM: imx: Add cpu frequency scaling support
  ARM i.MX35: Add devicetree support.
  ARM: imx: update imx_v6_v7_defconfig
  ARM: imx6sl: Add missing spba clock to clock tree
  ARM: imx6sl: Add missing pll4_audio_div to the clock tree
  ARM: imx6: Derive spdif clock from pll3_pfd3_454m
  ARM: imx: use __initconst for const init definition
  ARM i.MX5: fix obvious typo in ldb_di0_gate clk definition
  ARM i.MX5: set CAN peripheral clock to 24 MHz parent
  ARM: imx: pllv1: Fix PLL calculation for i.MX27
  ARM i.MX5: fix "shift" value for lp_apm_sel on i.MX50 and i.MX53
  ARM: imx: imx53: Add SATA PHY clock
  ARM: imx_v6_v7_defconfig: Enable STMPE touchscreen
  ARM: imx: rename IMX6SL_CLK_CLK_END to IMX6SL_CLK_END
  ARM: imx: select PINCTRL at sub-architecure level
  ...

Signed-off-by: Olof Johansson <olof@lixom.net>

Add appropriate UART address definitions and support defines for using the
UARTs of the Freescale IMX50 SoC as debug ports.

Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Stop writing to the UART clock divider registers in the Tegra DEBUG_LL
code. This allows the DEBUG_LL output to use whatever baud rate was set
up by the bootloader. Some users are using higher rates than 115200.

This removes the only usage of tegra_uart_config[3], so reduce the size
allocated for that array.

Finally, fix busyuart() so that it only waits for THRE and not TEMT. For
some reason, TEMT doesn't get asserted (at least on Tegra30 Beaver) at
9600 baud, even though it does at 115200 baud. This sounds like a HW bug,
but I haven't investigated. For reference, U-Boot's serial code has
always only checked THRE, and not checked TEMT.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Paul Walmsley <pwalmsley@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>

The DEBUG_LL UART address is mapped as an MMU section, hence, the
virtual address must be section-aligned. Sections are 1MB without LPAE
and 2MB with LPAE. Tegra's virtual address was only aligned to 1MB, and
hence the mapping was set up incorrectly with LPAE enabled, thus causing
a hang early during boot. Fix this by picking a different virtual address
that is aligned to 2MB.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>