Few minor fixes for omaps

Looks like we have wrong default memory size for beaglebone black,
it has at least 512 MB of RAM and not 256 MB. This causes an issue
when booted with GRUB2 that does not seem to pass memory info to
the kernel.

And for am43x-epos-evm the SPI pin directions need to be configured
for SPI to work.

* tag 'omap-for-fixes-whenever-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: am43x-epos-evm: set data pin directions for spi0 and spi1
  ARM: dts: am335x-boneblack-common: fix memory size

Link: https://lore.kernel.org/r/pull-1579895109-287828@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>

Set d0 and d1 pin directions for spi0 and spi1 as per their pinmux.

Signed-off-by: Raag Jadav <raagjadav@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

BeagleBone Black series is equipped with 512MB RAM
whereas only 256MB is included from am335x-bone-common.dtsi

This leads to an issue with unusual setups when devicetree
is loaded by GRUB2 directly.

Signed-off-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Signed-off-by: Tony Lindgren <tony@atomide.com>

A couple of fixes for GPIO polarity and regulators on the A64
olinuxino.

* tag 'sunxi-fixes-for-5.5' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
  ARM: dts: sun8i: a83t: Correct USB3503 GPIOs polarity
  arm64: dts: allwinner: a64: olinuxino: Fix SDIO supply regulator
  arm64: dts: allwinner: a64: olinuxino: Fix eMMC supply regulator

Link: https://lore.kernel.org/r/582f4fda-38af-43e8-af58-957aee5b9dd8.lettre@localhost
Signed-off-by: Olof Johansson <olof@lixom.net>

i.MX fixes for 5.5, round 2:

 - Fix i.MX8MM SDMA1 AHB clock setting to remove a "Timeout waiting for CH0"
   error seen with UART1.
 - Correct compatible of RV3029 RTC device on imx6q-dhcom board.
 - Correct interrupt trigger type for magnetometer on board
   imx8mq-librem5-devkit.
 - A series from Anson Huang to fix vdd3p0 power supplier for a few NXP
   development board.
 - Fix imx6q-icore-mipi board to use 1.5 version of i.Core MX6DL, so
   that Ethernet interface on the board works properly.
 - Fix Toradex Colibri board to get NAND flash support back.
 - Fix SGTL5000 VDDIO regulator connection for imx6q-dhcom, which
   is connected to PMIC SW2 output rather than a fixed 3V3 rail.
 - Fix 'reg' of CPU node on imx7ulp to get rid of a warning given by
   kernel.
 - Fix endian setting for DCFG on LS1028A SoC, so that register access
   of DCFG becomes correct.

* tag 'imx-fixes-5.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  ARM: dts: imx7: Fix Toradex Colibri iMX7S 256MB NAND flash support
  ARM: dts: imx6sll-evk: Remove incorrect power supply assignment
  ARM: dts: imx6sl-evk: Remove incorrect power supply assignment
  ARM: dts: imx6sx-sdb: Remove incorrect power supply assignment
  ARM: dts: imx6qdl-sabresd: Remove incorrect power supply assignment
  ARM: dts: imx6q-icore-mipi: Use 1.5 version of i.Core MX6DL
  arm64: dts: imx8mq-librem5-devkit: use correct interrupt for the magnetometer
  ARM: dts: imx6q-dhcom: Fix SGTL5000 VDDIO regulator connection
  ARM: dts: imx7ulp: fix reg of cpu node
  arm64: dts: imx8mm: Change SDMA1 ahb clock for imx8mm
  arm64: dts: ls1028a: fix endian setting for dcfg
  ARM: dts: imx6q-dhcom: fix rtc compatible

Link: https://lore.kernel.org/r/20200110011836.GW4456@T480
Signed-off-by: Olof Johansson <olof@lixom.net>

arm-soc: Amlogic fixes for v5.5-rc

* tag 'amlogic-fixes' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
  arm64: dts: meson-sm1-sei610: add gpio bluetooth interrupt
  dt-bindings: reset: meson8b: fix duplicate reset IDs
  soc: amlogic: meson-ee-pwrc: propagate errors from pm_genpd_init()
  soc: amlogic: meson-ee-pwrc: propagate PD provider registration errors
  ARM: dts: meson8: fix the size of the PMU registers
  arm64: dts: meson-sm1-sei610: gpio-keys: switch to IRQs

Link: https://lore.kernel.org/r/7hmuaweavi.fsf@baylibre.com
Signed-off-by: Olof Johansson <olof@lixom.net>

Turns out when introducing the eMMC version the gpmi node required for
NAND flash support got enabled exclusively on Colibri iMX7D 512MB.

Fixes: f928a4a377e4 ("ARM: dts: imx7: add Toradex Colibri iMX7D 1GB (eMMC) support")
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The vdd3p0 LDO's input should be from external USB VBUS directly, NOT
PMIC's power supply, the vdd3p0 LDO's target output voltage can be
controlled by SW, and it requires input voltage to be high enough, with
incorrect power supply assigned, if the power supply's voltage is lower
than the LDO target output voltage, it will return fail and skip the LDO
voltage adjustment, so remove the power supply assignment for vdd3p0 to
avoid such scenario.

Fixes: 96a9169cf621 ("ARM: dts: imx6sll-evk: Assign corresponding power supply for vdd3p0")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The vdd3p0 LDO's input should be from external USB VBUS directly, NOT
PMIC's power supply, the vdd3p0 LDO's target output voltage can be
controlled by SW, and it requires input voltage to be high enough, with
incorrect power supply assigned, if the power supply's voltage is lower
than the LDO target output voltage, it will return fail and skip the LDO
voltage adjustment, so remove the power supply assignment for vdd3p0 to
avoid such scenario.

Fixes: 3feea8805d6f ("ARM: dts: imx6sl-evk: Assign corresponding power supply for LDOs")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The vdd3p0 LDO's input should be from external USB VBUS directly, NOT
PMIC's power supply, the vdd3p0 LDO's target output voltage can be
controlled by SW, and it requires input voltage to be high enough, with
incorrect power supply assigned, if the power supply's voltage is lower
than the LDO target output voltage, it will return fail and skip the LDO
voltage adjustment, so remove the power supply assignment for vdd3p0 to
avoid such scenario.

Fixes: 37a4bdead109 ("ARM: dts: imx6sx-sdb: Assign corresponding power supply for LDOs")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>