linux-stable.git/arch/arm/boot, branch v5.2.8

ARM: dts: rockchip: Mark that the rk3288 timer might stop in suspend

2019-08-06T17:08:01+00:00

[ Upstream commit 8ef1ba39a9fa53d2205e633bc9b21840a275908e ]

This is similar to commit e6186820a745 ("arm64: dts: rockchip: Arch
counter doesn't tick in system suspend").  Specifically on the rk3288
it can be seen that the timer stops ticking in suspend if we end up
running through the "osc_disable" path in rk3288_slp_mode_set().  In
that path the 24 MHz clock will turn off and the timer stops.

To test this, I ran this on a Chrome OS filesystem:
  before=$(date); \
  suspend_stress_test -c1 --suspend_min=30 --suspend_max=31; \
  echo ${before}; date

...and I found that unless I plug in a device that requests USB wakeup
to be active that the two calls to "date" would show that fewer than
30 seconds passed.

NOTE: deep suspend (where the 24 MHz clock gets disabled) isn't
supported yet on upstream Linux so this was tested on a downstream
kernel.

Signed-off-by: Douglas Anderson 
Signed-off-by: Heiko Stuebner 
Signed-off-by: Sasha Levin

ARM: dts: rockchip: Make rk3288-veyron-mickey's emmc work again

2019-08-06T17:08:01+00:00

[ Upstream commit 99fa066710f75f18f4d9a5bc5f6a711968a581d5 ]

When I try to boot rk3288-veyron-mickey I totally fail to make the
eMMC work.  Specifically my logs (on Chrome OS 4.19):

  mmc_host mmc1: card is non-removable.
  mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
  mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0)
  mmc1: switch to bus width 8 failed
  mmc1: switch to bus width 4 failed
  mmc1: new high speed MMC card at address 0001
  mmcblk1: mmc1:0001 HAG2e 14.7 GiB
  mmcblk1boot0: mmc1:0001 HAG2e partition 1 4.00 MiB
  mmcblk1boot1: mmc1:0001 HAG2e partition 2 4.00 MiB
  mmcblk1rpmb: mmc1:0001 HAG2e partition 3 4.00 MiB, chardev (243:0)
  mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
  mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0)
  mmc1: switch to bus width 8 failed
  mmc1: switch to bus width 4 failed
  mmc1: tried to HW reset card, got error -110
  mmcblk1: error -110 requesting status
  mmcblk1: recovery failed!
  print_req_error: I/O error, dev mmcblk1, sector 0
  ...

When I remove the '/delete-property/mmc-hs200-1_8v' then everything is
hunky dory.

That line comes from the original submission of the mickey dts
upstream, so presumably at the time the HS200 was failing and just
enumerating things as a high speed device was fine.  ...or maybe it's
just that some mickey devices work when enumerating at "high speed",
just not mine?

In any case, hs200 seems good now.  Let's turn it on.

Signed-off-by: Douglas Anderson 
Signed-off-by: Heiko Stuebner 
Signed-off-by: Sasha Levin

ARM: dts: rockchip: Make rk3288-veyron-minnie run at hs200

2019-08-06T17:08:01+00:00

[ Upstream commit 1c0479023412ab7834f2e98b796eb0d8c627cd62 ]

As some point hs200 was failing on rk3288-veyron-minnie.  See commit
984926781122 ("ARM: dts: rockchip: temporarily remove emmc hs200 speed
from rk3288 minnie").  Although I didn't track down exactly when it
started working, it seems to work OK now, so let's turn it back on.

To test this, I booted from SD card and then used this script to
stress the enumeration process after fixing a memory leak [1]:
  cd /sys/bus/platform/drivers/dwmmc_rockchip
  for i in $(seq 1 3000); do
    echo "========================" $i
    echo ff0f0000.dwmmc > unbind
    sleep .5
    echo ff0f0000.dwmmc > bind
    while true; do
      if [ -e /dev/mmcblk2 ]; then
        break;
      fi
      sleep .1
    done
  done

It worked fine.

[1] https://lkml.kernel.org/r/20190503233526.226272-1-dianders@chromium.org

Signed-off-by: Douglas Anderson 
Signed-off-by: Heiko Stuebner 
Signed-off-by: Sasha Levin

ARM: dts: gemini: Set DIR-685 SPI CS as active low

2019-07-26T07:11:01+00:00

commit f90b8fda3a9d72a9422ea80ae95843697f94ea4a upstream.

The SPI to the display on the DIR-685 is active low, we were
just saved by the SPI library enforcing active low on everything
before, so set it as active low to avoid ambiguity.

Link: https://lore.kernel.org/r/20190715202101.16060-1-linus.walleij@linaro.org
Cc: stable@vger.kernel.org
Signed-off-by: Linus Walleij 
Signed-off-by: Olof Johansson 
Signed-off-by: Greg Kroah-Hartman

Merge tag 'davinci-fixes-for-v5.2-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into arm/fixes

2019-07-02T22:13:20+00:00

This set of patches fixes regressions introduced in v5.2 kernel when DA8xx
OHCI driver was converted over to use GPIO regulators.

* tag 'davinci-fixes-for-v5.2-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
  ARM: davinci: da830-evm: fix GPIO lookup for OHCI
  ARM: davinci: omapl138-hawk: add missing regulator constraints for OHCI
  ARM: davinci: da830-evm: add missing regulator constraints for OHCI
  + Linux 5.2-rc7

Signed-off-by: Olof Johansson

Merge tag 'mvebu-fixes-5.2-2' of git://git.infradead.org/linux-mvebu into arm/fixes

2019-07-01T22:14:09+00:00

mvebu fixes for 5.2 (part 2)

Use the armada-38x-uart compatible strings for Armada XP 98dx3236 SoCs
in order to not loose character anymore.

* tag 'mvebu-fixes-5.2-2' of git://git.infradead.org/linux-mvebu:
  ARM: dts: armada-xp-98dx3236: Switch to armada-38x-uart serial node

Signed-off-by: Olof Johansson

Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

2019-06-28T00:37:04+00:00

Pull ARM SoC fixes from Olof Johansson:
 "A smaller batch of fixes, nothing that stands out as risky or scary.

  Mostly DTS tweaks for a few issues:

   - GPU fixlets for Meson

   - CPU idle fix for LS1028A

   - PWM interrupt fixes for i.MX6UL

  Also, enable a driver (FSL_EDMA) on arm64 defconfig, and a warning and
  two MAINTAINER tweaks"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
  ARM: dts: imx6ul: fix PWM[1-4] interrupts
  ARM: omap2: remove incorrect __init annotation
  ARM: dts: gemini Fix up DNS-313 compatible string
  ARM: dts: Blank D-Link DIR-685 console
  arm64: defconfig: Enable FSL_EDMA driver
  arm64: dts: ls1028a: Fix CPU idle fail.
  MAINTAINERS: BCM53573: Add internal Broadcom mailing list
  MAINTAINERS: BCM2835: Add internal Broadcom mailing list
  ARM: dts: meson8b: fix the operating voltage of the Mali GPU
  ARM: dts: meson8b: drop undocumented property from the Mali GPU node
  ARM: dts: meson8: fix GPU interrupts and drop an undocumented property

ARM: dts: armada-xp-98dx3236: Switch to armada-38x-uart serial node

2019-06-27T15:34:38+00:00

Switch to the "marvell,armada-38x-uart" driver variant to empty
the UART buffer before writing to the UART_LCR register.

Signed-off-by: Joshua Scott 
Tested-by: Andrew Lunn 
Acked-by: Gregory CLEMENT .
Cc: stable@vger.kernel.org
Fixes: 43e28ba87708 ("ARM: dts: Use armada-370-xp as a base for armada-xp-98dx3236")
Signed-off-by: Gregory CLEMENT

Merge tag 'imx-fixes-5.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes

2019-06-25T11:20:08+00:00

i.MX fixes for 5.2, round 3:
 - A recent testing by Sébastien discovers that the PWM interrupts of
   i.MX6UL were wrongly coded in device tree.  It's a fix for it.

* tag 'imx-fixes-5.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  ARM: dts: imx6ul: fix PWM[1-4] interrupts

Signed-off-by: Olof Johansson

Merge tag 'amlogic-fixes' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into arm/fixes

2019-06-25T11:19:26+00:00

ARM: dts: Amlogic fixes for v5.2-rc
- fix GPU interrupts and operating voltage

* tag 'amlogic-fixes' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
  ARM: dts: meson8b: fix the operating voltage of the Mali GPU
  ARM: dts: meson8b: drop undocumented property from the Mali GPU node
  ARM: dts: meson8: fix GPU interrupts and drop an undocumented property

Signed-off-by: Olof Johansson