commit 8ac686d7dfed721102860ff2571e6b9f529ae81a upstream.

The assigned parent clocks should be normally specified in the consumer
device's DT node, this ensures respective driver always sees correct clock
settings when required.

This patch fixes regression in audio subsystem on Odroid XU3/XU4 boards
that appeared after commits:

commit 647d04f8e07a ("ASoC: samsung: i2s: Ensure the RCLK rate is properly determined")
commit 995e73e55f46 ("ASoC: samsung: i2s: Fix rclk_srcrate handling")
commit 48279c53fd1d ("ASoC: samsung: i2s: Prevent external abort on exynos5433 I2S1 access")

Without this patch the driver gets wrong clock as the I2S function clock
(op_clk) in probe() and effectively the clock which is finally assigned
from DT is not being enabled/disabled in the runtime resume/suspend ops.

Without the above listed commits the EXYNOS_I2S_BUS clock was always set
as parent of CLK_I2S_RCLK_SRC regardless of DT settings so there was no issue
with not enabled EXYNOS_SCLK_I2S.

Cc: <stable@vger.kernel.org> # 4.17.x
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Allwinner fixes for 4.20

One small fix for a regulator range on the Banana Pi M3

* tag 'sunxi-fixes-for-4.20' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
  ARM: dts: sun8i: a83t: bananapi-m3: increase vcc-pd voltage to 3.3V

Signed-off-by: Olof Johansson <olof@lixom.net>

i.MX fixes for 4.20, round 3:
 - A couple of fixes on imx7d-pico and imx7d-nitrogen7 boards to correct
   the description of the Wifi clock.
 - Change SW2ISO count to get a safer ARM LDO ramp-up time, so that
   different boards can be covered. This fixes the ARM LDO failure seen
   on some customer boards.

* tag 'imx-fixes-4.20-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  ARM: dts: imx7d-nitrogen7: Fix the description of the Wifi clock
  ARM: imx: update the cpu power up timing setting on i.mx6sx
  ARM: dts: imx7d-pico: Describe the Wifi clock

Signed-off-by: Olof Johansson <olof@lixom.net>

According to bindings/regulator/fixed-regulator.txt the 'clocks' and
'clock-names' properties are not valid ones.

In order to turn on the Wifi clock the correct location for describing
the CLKO2 clock is via a mmc-pwrseq handle, so do it accordingly.

Fixes: 56354959cfec ("ARM: dts: imx: add Boundary Devices Nitrogen7 board")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The Wifi chip should be clocked by a 32kHz clock coming from i.MX7D
CLKO2 output pin, so describe the pinmux and clock hierarchy in the
device tree to allow the Wifi chip to be properly clocked.

Managed to successfully test Wifi with such change. Used the standard
nvram.txt file provided by TechNexion, which selects an external 32kHz
clock for the Wifi chip by default.

Fixes: 99a52450c707 ("ARM: dts: imx7d-pico: Add Wifi support")
Suggested-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Tested-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This pull request contains Broadcom ARM-based SoCs Device Tree fixes,
please pull the following for 4.20:

- Stefan fixes the polariy of the Wi-Fi reset GPIOs signals which would
  break on Raspberry Pi 3B and 3B+

* tag 'arm-soc/for-4.20/devicetree-fixes' of https://github.com/Broadcom/stblinux:
  ARM: dts: bcm2837: Fix polarity of wifi reset GPIOs

Signed-off-by: Olof Johansson <olof@lixom.net>

There's a bug in dtc in checking for duplicate node names when there's
another section (e.g. "/ { };"). In this case, skeleton.dtsi provides
another section. Upon removal of skeleton.dtsi, the dtb fails to build
due to a duplicate node 'fixedregulator@0'. As both nodes were pretty
much the same 3.3V fixed regulator, it hasn't really mattered. Fix this
by renaming the nodes to something unique. In the process, drop the
unit-address which shouldn't be present wtihout reg property.

Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

The commit b1b8f45b3130 ("ARM: dts: bcm2837: Add missing GPIOs of Expander")
introduced a wifi power sequence. Unfortunately the polarity of the reset
GPIOs were wrong and broke the wifi support on Raspberry Pi 3 B and
later in 3 B+. This wasn't discovered before since the power sequence
takes only effect in case the relevant MMC driver is compiled as a module.

Fixes: b1b8f45b3130 ("ARM: dts: bcm2837: Add missing GPIOs of Expander")
Cc: stable@vger.kernel.org
Reported-by: Matthias Lueschner <lueschem@gmail.com>
Link: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=911443
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

i.MX fixes for 4.20, round 2:
 - Reomve non-existing EEPROM device from imx51-zii-rdu1 board.
   It was added by mistake.

* tag 'imx-fixes-4.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  ARM: dts: imx51-zii-rdu1: Remove EEPROM node

Signed-off-by: Olof Johansson <olof@lixom.net>

Few minor fixes for omaps for v4.20-rc cycle

This set of fixes contains minor regression fixes for LogicPD dts files
for MMC pinctrl and interrupts. There is also one section annotation fix
that shows up with Clang, and a fix for an unitialized field for omap1.

* tag 'omap-for-v4.20/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: OMAP1: ams-delta: Fix possible use of uninitialized field
  ARM: dts: am3517-som: Fix WL127x Wifi interrupt
  ARM: dts: logicpd-somlv: Fix interrupt on mmc3_dat1
  ARM: dts: LogicPD Torpedo: Fix mmc3_dat1 interrupt
  ARM: dts: am3517: Fix pinmuxing for CD on MMC1
  ARM: OMAP2+: prm44xx: Fix section annotation on omap44xx_prm_enable_io_wakeup

Signed-off-by: Olof Johansson <olof@lixom.net>