linux-stable.git/arch/arm/boot, branch v4.19.78 Linux kernel stable tree ARM: dts: exynos: Mark LDO10 as always-on on Peach Pit/Pi Chromebooks 2019-10-05T11:09:53+00:00 Marek Szyprowski m.szyprowski@samsung.com 2019-08-30T12:52:42+00:00 6fceb241dc76951d88e8f64384248dfc21fa8f05 [ Upstream commit 5b0eeeaa37615df37a9a30929b73e9defe61ca84 ] Commit aff138bf8e37 ("ARM: dts: exynos: Add TMU nodes regulator supply for Peach boards") assigned LDO10 to Exynos Thermal Measurement Unit, but it turned out that it supplies also some other critical parts and board freezes/crashes when it is turned off. The mentioned commit made Exynos TMU a consumer of that regulator and in typical case Exynos TMU driver keeps it enabled from early boot. However there are such configurations (example is multi_v7_defconfig), in which some of the regulators are compiled as modules and are not available from early boot. In such case it may happen that LDO10 is turned off by regulator core, because it has no consumers yet (in this case consumer drivers cannot get it, because the supply regulators for it are not yet available). This in turn causes the board to crash. This patch restores 'always-on' property for the LDO10 regulator. Fixes: aff138bf8e37 ("ARM: dts: exynos: Add TMU nodes regulator supply for Peach boards") Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 5b0eeeaa37615df37a9a30929b73e9defe61ca84 ]

Commit aff138bf8e37 ("ARM: dts: exynos: Add TMU nodes regulator supply
for Peach boards") assigned LDO10 to Exynos Thermal Measurement Unit,
but it turned out that it supplies also some other critical parts and
board freezes/crashes when it is turned off.

The mentioned commit made Exynos TMU a consumer of that regulator and in
typical case Exynos TMU driver keeps it enabled from early boot. However
there are such configurations (example is multi_v7_defconfig), in which
some of the regulators are compiled as modules and are not available
from early boot. In such case it may happen that LDO10 is turned off by
regulator core, because it has no consumers yet (in this case consumer
drivers cannot get it, because the supply regulators for it are not yet
available). This in turn causes the board to crash. This patch restores
'always-on' property for the LDO10 regulator.

Fixes: aff138bf8e37 ("ARM: dts: exynos: Add TMU nodes regulator supply for Peach boards")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
ARM: dts: imx7-colibri: disable HS400 2019-10-05T11:09:44+00:00 Stefan Agner stefan.agner@toradex.com 2019-08-12T14:21:17+00:00 dfaf60580191207627a85739850799bbb13280f4 [ Upstream commit a95fbda08ee20cd063ce5826e0df95a2c22ea8c5 ] Force HS200 by masking bit 63 of the SDHCI capability register. The i.MX ESDHC driver uses SDHCI_QUIRK2_CAPS_BIT63_FOR_HS400. With that the stack checks bit 63 to descide whether HS400 is available. Using sdhci-caps-mask allows to mask bit 63. The stack then selects HS200 as operating mode. This prevents rare communication errors with minimal effect on performance: sdhci-esdhc-imx 30b60000.usdhc: warning! HS400 strobe DLL status REF not lock! Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit a95fbda08ee20cd063ce5826e0df95a2c22ea8c5 ]

Force HS200 by masking bit 63 of the SDHCI capability register.
The i.MX ESDHC driver uses SDHCI_QUIRK2_CAPS_BIT63_FOR_HS400. With
that the stack checks bit 63 to descide whether HS400 is available.
Using sdhci-caps-mask allows to mask bit 63. The stack then selects
HS200 as operating mode.

This prevents rare communication errors with minimal effect on
performance:
	sdhci-esdhc-imx 30b60000.usdhc: warning! HS400 strobe DLL
		status REF not lock!

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
ARM: dts: imx7d: cl-som-imx7: make ethernet work again 2019-10-05T11:09:43+00:00 André Draszik git@andred.net 2019-08-09T03:12:27+00:00 c20ee5d906eca0d8a935999c17cd1dbb37c72fc5 [ Upstream commit 9846a4524ac90b63496580b7ad50674b40d92a8f ] Recent changes to the atheros at803x driver caused ethernet to stop working on this board. In particular commit 6d4cd041f0af ("net: phy: at803x: disable delay only for RGMII mode") and commit cd28d1d6e52e ("net: phy: at803x: Disable phy delay for RGMII mode") fix the AR8031 driver to configure the phy's (RX/TX) delays as per the 'phy-mode' in the device tree. This now prevents ethernet from working on this board. It used to work before those commits, because the AR8031 comes out of reset with RX delay enabled, and the at803x driver didn't touch the delay configuration at all when "rgmii" mode was selected, and because arch/arm/mach-imx/mach-imx7d.c:ar8031_phy_fixup() unconditionally enables TX delay. Since above commits ar8031_phy_fixup() also has no effect anymore, and the end-result is that all delays are disabled in the phy, no ethernet. Update the device tree to restore functionality. Signed-off-by: André Draszik <git@andred.net> CC: Ilya Ledvich <ilya@compulab.co.il> CC: Igor Grinberg <grinberg@compulab.co.il> CC: Rob Herring <robh+dt@kernel.org> CC: Mark Rutland <mark.rutland@arm.com> CC: Shawn Guo <shawnguo@kernel.org> CC: Sascha Hauer <s.hauer@pengutronix.de> CC: Pengutronix Kernel Team <kernel@pengutronix.de> CC: Fabio Estevam <festevam@gmail.com> CC: NXP Linux Team <linux-imx@nxp.com> CC: devicetree@vger.kernel.org CC: linux-arm-kernel@lists.infradead.org Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 9846a4524ac90b63496580b7ad50674b40d92a8f ]

Recent changes to the atheros at803x driver caused
ethernet to stop working on this board.
In particular commit 6d4cd041f0af
("net: phy: at803x: disable delay only for RGMII mode")
and commit cd28d1d6e52e
("net: phy: at803x: Disable phy delay for RGMII mode")
fix the AR8031 driver to configure the phy's (RX/TX)
delays as per the 'phy-mode' in the device tree.

This now prevents ethernet from working on this board.

It used to work before those commits, because the
AR8031 comes out of reset with RX delay enabled, and
the at803x driver didn't touch the delay configuration
at all when "rgmii" mode was selected, and because
arch/arm/mach-imx/mach-imx7d.c:ar8031_phy_fixup()
unconditionally enables TX delay.

Since above commits ar8031_phy_fixup() also has no
effect anymore, and the end-result is that all delays
are disabled in the phy, no ethernet.

Update the device tree to restore functionality.

Signed-off-by: André Draszik <git@andred.net>
CC: Ilya Ledvich <ilya@compulab.co.il>
CC: Igor Grinberg <grinberg@compulab.co.il>
CC: Rob Herring <robh+dt@kernel.org>
CC: Mark Rutland <mark.rutland@arm.com>
CC: Shawn Guo <shawnguo@kernel.org>
CC: Sascha Hauer <s.hauer@pengutronix.de>
CC: Pengutronix Kernel Team <kernel@pengutronix.de>
CC: Fabio Estevam <festevam@gmail.com>
CC: NXP Linux Team <linux-imx@nxp.com>
CC: devicetree@vger.kernel.org
CC: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
ARM: dts: dra74x: Fix iodelay configuration for mmc3 2019-09-21T05:16:50+00:00 Faiz Abbas faiz_abbas@ti.com 2019-08-07T10:52:38+00:00 a8919f8d352f7e802d8f7757e6212ff0d98d9890 [ Upstream commit 07f9a8be66a9bd86f9eaedf8f8aeb416195adab8 ] According to the latest am572x[1] and dra74x[2] data manuals, mmc3 default, hs, sdr12 and sdr25 modes use iodelay values given in MMC3_MANUAL1. Set the MODE_SELECT bit for these so that manual mode is selected and correct iodelay values can be configured. [1] http://www.ti.com/lit/ds/symlink/am5728.pdf [2] http://www.ti.com/lit/ds/symlink/dra746.pdf Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 07f9a8be66a9bd86f9eaedf8f8aeb416195adab8 ]

According to the latest am572x[1] and dra74x[2] data manuals, mmc3
default, hs, sdr12 and sdr25 modes use iodelay values given in
MMC3_MANUAL1. Set the MODE_SELECT bit for these so that manual mode is
selected and correct iodelay values can be configured.

[1] http://www.ti.com/lit/ds/symlink/am5728.pdf
[2] http://www.ti.com/lit/ds/symlink/dra746.pdf

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
ARM: dts: am57xx: Disable voltage switching for SD card 2019-09-21T05:16:47+00:00 Faiz Abbas faiz_abbas@ti.com 2019-06-19T10:24:54+00:00 f696ba6b122decf5c20d7c7774406002dd8d2772 [ Upstream commit fb59ee37cfe20d10d19568899d1458a58361246c ] If UHS speed modes are enabled, a compatible SD card switches down to 1.8V during enumeration. If after this a software reboot/crash takes place and on-chip ROM tries to enumerate the SD card, the difference in IO voltages (host @ 3.3V and card @ 1.8V) may end up damaging the card. The fix for this is to have support for power cycling the card in hardware (with a PORz/soft-reset line causing a power cycle of the card). Because the beaglebone X15 (rev A,B and C), am57xx-idks and am57xx-evms don't have this capability, disable voltage switching for these boards. The major effect of this is that the maximum supported speed mode is now high speed(50 MHz) down from SDR104(200 MHz). commit 88a748419b84 ("ARM: dts: am57xx-idk: Remove support for voltage switching for SD card") did this only for idk boards. Do it for all affected boards. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit fb59ee37cfe20d10d19568899d1458a58361246c ]

If UHS speed modes are enabled, a compatible SD card switches down to
1.8V during enumeration. If after this a software reboot/crash takes
place and on-chip ROM tries to enumerate the SD card, the difference in
IO voltages (host @ 3.3V and card @ 1.8V) may end up damaging the card.

The fix for this is to have support for power cycling the card in
hardware (with a PORz/soft-reset line causing a power cycle of the
card). Because the beaglebone X15 (rev A,B and C), am57xx-idks and
am57xx-evms don't have this capability, disable voltage switching for
these boards.

The major effect of this is that the maximum supported speed
mode is now high speed(50 MHz) down from SDR104(200 MHz).

commit 88a748419b84 ("ARM: dts: am57xx-idk: Remove support for voltage
switching for SD card") did this only for idk boards. Do it for all
affected boards.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
ARM: dts: gemini: Set DIR-685 SPI CS as active low 2019-09-16T06:22:19+00:00 Linus Walleij linus.walleij@linaro.org 2019-07-15T20:21:01+00:00 bab0ff2d87db2b2c46c4158f28d37699e396c3c4 [ Upstream commit f90b8fda3a9d72a9422ea80ae95843697f94ea4a ] The SPI to the display on the DIR-685 is active low, we were just saved by the SPI library enforcing active low on everything before, so set it as active low to avoid ambiguity. Link: https://lore.kernel.org/r/20190715202101.16060-1-linus.walleij@linaro.org Cc: stable@vger.kernel.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit f90b8fda3a9d72a9422ea80ae95843697f94ea4a ]

The SPI to the display on the DIR-685 is active low, we were
just saved by the SPI library enforcing active low on everything
before, so set it as active low to avoid ambiguity.

Link: https://lore.kernel.org/r/20190715202101.16060-1-linus.walleij@linaro.org
Cc: stable@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
ARM: dts: qcom: ipq4019: enlarge PCIe BAR range 2019-09-16T06:22:11+00:00 Christian Lamparter chunkeey@gmail.com 2019-02-26T00:12:01+00:00 0a0176f93ea966f6b2bc71b00164b4d7e3b36af8 [ Upstream commit f3e35357cd460a8aeb48b8113dc4b761a7d5c828 ] David Bauer reported that the VDSL modem (attached via PCIe) on his AVM Fritz!Box 7530 was complaining about not having enough space in the BAR. A closer inspection of the old qcom-ipq40xx.dtsi pulled from the GL-iNet repository listed: | qcom,pcie@80000 { | compatible = "qcom,msm_pcie"; | reg = <0x80000 0x2000>, | <0x99000 0x800>, | <0x40000000 0xf1d>, | <0x40000f20 0xa8>, | <0x40100000 0x1000>, | <0x40200000 0x100000>, | <0x40300000 0xd00000>; | reg-names = "parf", "phy", "dm_core", "elbi", | "conf", "io", "bars"; Matching the reg-names with the listed reg leads to <0xd00000> as the size for the "bars". Cc: stable@vger.kernel.org BugLink: https://www.mail-archive.com/openwrt-devel@lists.openwrt.org/msg45212.html Reported-by: David Bauer <mail@david-bauer.net> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Andy Gross <agross@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit f3e35357cd460a8aeb48b8113dc4b761a7d5c828 ]

David Bauer reported that the VDSL modem (attached via PCIe)
on his AVM Fritz!Box 7530 was complaining about not having
enough space in the BAR. A closer inspection of the old
qcom-ipq40xx.dtsi pulled from the GL-iNet repository listed:

| qcom,pcie@80000 {
|	compatible = "qcom,msm_pcie";
|	reg = <0x80000 0x2000>,
|	      <0x99000 0x800>,
|	      <0x40000000 0xf1d>,
|	      <0x40000f20 0xa8>,
|	      <0x40100000 0x1000>,
|	      <0x40200000 0x100000>,
|	      <0x40300000 0xd00000>;
|	reg-names = "parf", "phy", "dm_core", "elbi",
|			"conf", "io", "bars";

Matching the reg-names with the listed reg leads to
<0xd00000> as the size for the "bars".

Cc: stable@vger.kernel.org
BugLink: https://www.mail-archive.com/openwrt-devel@lists.openwrt.org/msg45212.html
Reported-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Andy Gross <agross@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
ARM: dts: qcom: ipq4019: Fix MSI IRQ type 2019-09-16T06:22:11+00:00 Niklas Cassel niklas.cassel@linaro.org 2019-01-24T13:00:47+00:00 445a78ea3f906518cb85163b71dad3502a91b779 [ Upstream commit 97131f85c08e024df49480ed499aae8fb754067f ] The databook clearly states that the MSI IRQ (msi_ctrl_int) is a level triggered interrupt. The msi_ctrl_int will be high for as long as any MSI status bit is set, thus the IRQ type should be set to IRQ_TYPE_LEVEL_HIGH, causing the IRQ handler to keep getting called, as long as any MSI status bit is set. A git grep shows that ipq4019 is the only SoC using snps,dw-pcie that has configured this IRQ incorrectly. Not having the correct IRQ type defined will cause us to lose interrupts, which in turn causes timeouts in the PCIe endpoint drivers. Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Andy Gross <andy.gross@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 97131f85c08e024df49480ed499aae8fb754067f ]

The databook clearly states that the MSI IRQ (msi_ctrl_int) is a level
triggered interrupt.

The msi_ctrl_int will be high for as long as any MSI status bit is set,
thus the IRQ type should be set to IRQ_TYPE_LEVEL_HIGH, causing the
IRQ handler to keep getting called, as long as any MSI status bit is set.

A git grep shows that ipq4019 is the only SoC using snps,dw-pcie that has
configured this IRQ incorrectly.

Not having the correct IRQ type defined will cause us to lose interrupts,
which in turn causes timeouts in the PCIe endpoint drivers.

Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
ARM: dts: qcom: ipq4019: fix PCI range 2019-09-16T06:22:11+00:00 Mathias Kresin dev@kresin.me 2018-07-25T08:37:48+00:00 df1216d8bc866336e393240466c875a0bac4049f [ Upstream commit da89f500cb55fb3f19c4b399b46d8add0abbd4d6 ] The PCI range is invalid and PCI attached devices doen't work. Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: John Crispin <john@phrozen.org> Signed-off-by: Andy Gross <andy.gross@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit da89f500cb55fb3f19c4b399b46d8add0abbd4d6 ]

The PCI range is invalid and PCI attached devices doen't work.

Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
ARM: dts: bcm: bcm47094: add missing #cells for mdio-bus-mux 2019-08-16T08:12:49+00:00 Arnd Bergmann arnd@arndb.de 2019-07-22T14:55:52+00:00 bb41940c89bd16d55afd81335719e4fc7205c469 [ Upstream commit 3a9d2569e45cb02769cda26fee4a02126867c934 ] The mdio-bus-mux has no #address-cells/#size-cells property, which causes a few dtc warnings: arch/arm/boot/dts/bcm47094-linksys-panamera.dts:129.4-18: Warning (reg_format): /mdio-bus-mux/mdio@200:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1) arch/arm/boot/dts/bcm47094-linksys-panamera.dtb: Warning (pci_device_bus_num): Failed prerequisite 'reg_format' arch/arm/boot/dts/bcm47094-linksys-panamera.dtb: Warning (i2c_bus_reg): Failed prerequisite 'reg_format' arch/arm/boot/dts/bcm47094-linksys-panamera.dtb: Warning (spi_bus_reg): Failed prerequisite 'reg_format' arch/arm/boot/dts/bcm47094-linksys-panamera.dts:128.22-132.5: Warning (avoid_default_addr_size): /mdio-bus-mux/mdio@200: Relying on default #address-cells value arch/arm/boot/dts/bcm47094-linksys-panamera.dts:128.22-132.5: Warning (avoid_default_addr_size): /mdio-bus-mux/mdio@200: Relying on default #size-cells value Add the normal cell numbers. Link: https://lore.kernel.org/r/20190722145618.1155492-1-arnd@arndb.de Fixes: 2bebdfcdcd0f ("ARM: dts: BCM5301X: Add support for Linksys EA9500") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Sasha Levin <sashal@kernel.org> 
[ Upstream commit 3a9d2569e45cb02769cda26fee4a02126867c934 ]

The mdio-bus-mux has no #address-cells/#size-cells property,
which causes a few dtc warnings:

arch/arm/boot/dts/bcm47094-linksys-panamera.dts:129.4-18: Warning (reg_format): /mdio-bus-mux/mdio@200:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)
arch/arm/boot/dts/bcm47094-linksys-panamera.dtb: Warning (pci_device_bus_num): Failed prerequisite 'reg_format'
arch/arm/boot/dts/bcm47094-linksys-panamera.dtb: Warning (i2c_bus_reg): Failed prerequisite 'reg_format'
arch/arm/boot/dts/bcm47094-linksys-panamera.dtb: Warning (spi_bus_reg): Failed prerequisite 'reg_format'
arch/arm/boot/dts/bcm47094-linksys-panamera.dts:128.22-132.5: Warning (avoid_default_addr_size): /mdio-bus-mux/mdio@200: Relying on default #address-cells value
arch/arm/boot/dts/bcm47094-linksys-panamera.dts:128.22-132.5: Warning (avoid_default_addr_size): /mdio-bus-mux/mdio@200: Relying on default #size-cells value

Add the normal cell numbers.

Link: https://lore.kernel.org/r/20190722145618.1155492-1-arnd@arndb.de
Fixes: 2bebdfcdcd0f ("ARM: dts: BCM5301X: Add support for Linksys EA9500")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>