linux-stable.git/arch/arm/boot, branch v4.14.78

ARM: dts: at91: add new compatibility string for macb on sama5d3

2018-10-18T07:16:22+00:00

[ Upstream commit 321cc359d899a8e988f3725d87c18a628e1cc624 ]

We need this new compatibility string as we experienced different behavior
for this 10/100Mbits/s macb interface on this particular SoC.
Backward compatibility is preserved as we keep the alternative strings.

Signed-off-by: Nicolas Ferre 
Signed-off-by: David S. Miller 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

ARM: dts: omap4-droid4: Fix emmc errors seen on some devices

2018-10-04T00:00:59+00:00

[ Upstream commit 2d59bb602314a4b2593fde267734266b5e872dd0 ]

Otherwise we can get the following errors occasionally on some devices:

mmc1: tried to HW reset card, got error -110
mmcblk1: error -110 requesting status
mmcblk1: recovery failed!
print_req_error: I/O error, dev mmcblk1, sector 14329
...

I have one device that hits this error almost on every boot, and another
one that hits it only rarely with the other ones I've used behave without
problems. I'm not sure if the issue is related to a particular eMMC card
model, but in case it is, both of the machines with issues have:

# cat /sys/class/mmc_host/mmc1/mmc1:0001/manfid \
/sys/class/mmc_host/mmc1/mmc1:0001/oemid \
/sys/class/mmc_host/mmc1/mmc1:0001/name
0x000045
0x0100
SEM16G

and the working ones have:

0x000011
0x0100
016G92

Note that "ti,non-removable" is different as omap_hsmmc_reg_get() does not
call omap_hsmmc_disable_boot_regulators() if no_regulator_off_init is set.
And currently we set no_regulator_off_init only for "ti,non-removable" and
not for "non-removable". It seems that we should have "non-removable" with
some other mmc generic property behave in the same way instead of having to
use a non-generic property. But let's fix the issue first.

Fixes: 7e2f8c0ae670 ("ARM: dts: Add minimal support for motorola droid 4
xt894")
Cc: Marcel Partap 
Cc: Merlijn Wajer 
Cc: Michael Scott 
Cc: NeKit 
Cc: Pavel Machek 
Cc: Sebastian Reichel 
Signed-off-by: Tony Lindgren 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

Revert "ARM: dts: imx7d: Invert legacy PCI irq mapping"

2018-10-04T00:00:59+00:00

[ Upstream commit 538d6e9d597584e80514698e24321645debde78f ]

This reverts commit 1c86c9dd82f859b474474a7fee0d5195da2c9c1d.

That commit followed the reference manual but unfortunately the imx7d
manual is incorrect.

Tested with ath9k pcie card and confirmed internally.

Signed-off-by: Leonard Crestez 
Acked-by: Lucas Stach 
Fixes: 1c86c9dd82f8 ("ARM: dts: imx7d: Invert legacy PCI irq mapping")
Signed-off-by: Shawn Guo 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

ARM: dts: dra7: fix DCAN node addresses

2018-10-04T00:00:54+00:00

[ Upstream commit 949bdcc8a97c6078f21c8d4966436b117f2e4cd3 ]

Fix the DT node addresses to match the reg property addresses,
which were verified to match the TRM:
http://www.ti.com/lit/pdf/sprui30

Cc: Roger Quadros 
Signed-off-by: Kevin Hilman 
Acked-by: Roger Quadros 
Signed-off-by: Tony Lindgren 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

arm: dts: mediatek: Add missing cooling device properties for CPUs

2018-10-04T00:00:52+00:00

[ Upstream commit 0c7f7a5150023f3c6f0b27c4d4940ce3dfaf62cc ]

The cooling device properties, like "#cooling-cells" and
"dynamic-power-coefficient", should either be present for all the CPUs
of a cluster or none. If these are present only for a subset of CPUs of
a cluster then things will start falling apart as soon as the CPUs are
brought online in a different order. For example, this will happen
because the operating system looks for such properties in the CPU node
it is trying to bring up, so that it can register a cooling device.

Add such missing properties.

Signed-off-by: Viresh Kumar 
Signed-off-by: Matthias Brugger 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

ARM: dts: ls1021a: Add missing cooling device properties for CPUs

2018-10-04T00:00:48+00:00

[ Upstream commit 47768f372eae030db6fab5225f9504a820d2c07f ]

The cooling device properties, like "#cooling-cells" and
"dynamic-power-coefficient", should either be present for all the CPUs
of a cluster or none. If these are present only for a subset of CPUs of
a cluster then things will start falling apart as soon as the CPUs are
brought online in a different order. For example, this will happen
because the operating system looks for such properties in the CPU node
it is trying to bring up, so that it can register a cooling device.

Add such missing properties.

Signed-off-by: Viresh Kumar 
Signed-off-by: Shawn Guo 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

ARM: dts: qcom: msm8974-hammerhead: increase load on l20 for sdhci

2018-09-26T06:38:04+00:00

[ Upstream commit 03864e57770a9541e7ff3990bacf2d9a2fffcd5d ]

The kernel would not boot on the hammerhead hardware due to the
following error:

mmc0: Timeout waiting for hardware interrupt.
mmc0: sdhci: ============ SDHCI REGISTER DUMP ===========
mmc0: sdhci: Sys addr:  0x00000200 | Version:  0x00003802
mmc0: sdhci: Blk size:  0x00000200 | Blk cnt:  0x00000200
mmc0: sdhci: Argument:  0x00000000 | Trn mode: 0x00000023
mmc0: sdhci: Present:   0x03e80000 | Host ctl: 0x00000034
mmc0: sdhci: Power:     0x00000001 | Blk gap:  0x00000000
mmc0: sdhci: Wake-up:   0x00000000 | Clock:    0x00000007
mmc0: sdhci: Timeout:   0x0000000e | Int stat: 0x00000000
mmc0: sdhci: Int enab:  0x02ff900b | Sig enab: 0x02ff100b
mmc0: sdhci: AC12 err:  0x00000000 | Slot int: 0x00000000
mmc0: sdhci: Caps:      0x642dc8b2 | Caps_1:   0x00008007
mmc0: sdhci: Cmd:       0x00000c1b | Max curr: 0x00000000
mmc0: sdhci: Resp[0]:   0x00000c00 | Resp[1]:  0x00000000
mmc0: sdhci: Resp[2]:   0x00000000 | Resp[3]:  0x00000000
mmc0: sdhci: Host ctl2: 0x00000008
mmc0: sdhci: ADMA Err:  0x00000000 | ADMA Ptr: 0x70040220
mmc0: sdhci: ============================================
mmc0: Card stuck in wrong state! mmcblk0 card_busy_detect status: 0xe00
mmc0: cache flush error -110
mmc0: Reset 0x1 never completed.

This patch increases the load on l20 to 0.2 amps for the sdhci
and allows the device to boot normally.

Signed-off-by: Bhushan Shah 
Signed-off-by: Brian Masney 
Suggested-by: Bjorn Andersson 
Tested-by: Brian Masney 
Signed-off-by: Andy Gross 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

ARM: tegra: Fix Tegra30 Cardhu PCA954x reset

2018-09-09T17:55:59+00:00

commit 6e1811900b6fe6f2b4665dba6bd6ed32c6b98575 upstream.

On all versions of Tegra30 Cardhu, the reset signal to the NXP PCA9546
I2C mux is connected to the Tegra GPIO BB0. Currently, this pin on the
Tegra is not configured as a GPIO but as a special-function IO (SFIO)
that is multiplexing the pin to an I2S controller. On exiting system
suspend, I2C commands sent to the PCA9546 are failing because there is
no ACK. Although it is not possible to see exactly what is happening
to the reset during suspend, by ensuring it is configured as a GPIO
and driven high, to de-assert the reset, the failures are no longer
seen.

Please note that this GPIO is also used to drive the reset signal
going to the camera connector on the board. However, given that there
is no camera support currently for Cardhu, this should not have any
impact.

Fixes: 40431d16ff11 ("ARM: tegra: enable PCA9546 on Cardhu")
Cc: stable@vger.kernel.org
Signed-off-by: Jon Hunter 
Signed-off-by: Thierry Reding 
Signed-off-by: Greg Kroah-Hartman

ARM: dts: imx6: RDU2: fix irq type for mv88e6xxx switch

2018-08-24T11:09:20+00:00

[ Upstream commit e01a06c8089132bb4da035c6a83df23916ca3ebf ]

The Marvell switches report their interrupts in a level sensitive way.
When using edge sensitive detection a race condition in the interrupt
handler of the swich might result in the OS to miss all future events
which might make the switch non-functional.

The problem is that both mv88e6xxx_g2_irq_thread_fn() and
mv88e6xxx_g1_irq_thread_work() sample the irq cause register
(MV88E6XXX_G2_INT_SRC and MV88E6XXX_G1_STS respectively) once and then
handle the observed sources. If after sampling but before all observed
irq sources are handled a new irq source gets active this is not noticed
by the handler which returns unsuspecting, but the interrupt line stays
active which prevents the edge detector to kick in.

All device trees but imx6qdl-zii-rdu2 get this right (most of them by
not specifying an interrupt parent). So fix imx6qdl-zii-rdu2
accordingly.

Signed-off-by: Uwe Kleine-König 
Fixes: f64992d1a916 ("ARM: dts: imx6: RDU2: Add Switch interrupts")
Reviewed-by: Andrew Lunn 
Signed-off-by: Shawn Guo 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman

ARM: dts: am3517.dtsi: Disable reference to OMAP3 OTG controller

2018-08-24T11:09:16+00:00

[ Upstream commit 923847413f7316b5ced3491769b3fefa6c56a79a ]

The AM3517 has a different OTG controller location than the OMAP3,
which is included from omap3.dtsi.  This results in a hwmod error.
Since the AM3517 has a different OTG controller address, this patch
disabes one that is isn't available.

Signed-off-by: Adam Ford 
Signed-off-by: Tony Lindgren 
Signed-off-by: Sasha Levin 
Signed-off-by: Greg Kroah-Hartman