commit 5e794de514f56de1e78e979ca09c56a91aa2e9f1 upstream.

The PWM block is required for system clock source so it must be always
enabled. This patch fixes boot issues on SMDK6410 which did not have
the node enabled explicitly for other purposes.

Fixes: eeb93d02 ("clocksource: of: Respect device tree node status")

Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit be6688350a4470e417aaeca54d162652aab40ac5 upstream.

OMAP wdt driver supports only ti,omap3-wdt compatible. In DRA7 dt
wdt compatible property is defined as ti,omap4-wdt by mistake instead of
ti,omap3-wdt. Correcting the typo.

Fixes: 6e58b8f1daaf1a ("ARM: dts: DRA7: Add the dts files for dra7 SoC and dra7-evm board")
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d73f825e6efa723e81d9ffcc4949fe9f03f1df29 upstream.

The lcd0 node for am437x-sk-evm.dts contains bad LCD timings, and while
they seem to work with a quick test, doing for example blank/unblank
will give you a black display.

This patch updates the timings to the 'typical' values from the LCD spec
sheet.

Also, the compatible string is completely bogus, as
"osddisplays,osd057T0559-34ts" is _not_ a 480x272 panel. The panel on
the board is a newhaven one. Update the compatible string to reflect
this. Note that this hasn't caused any issues, as the "panel-dpi"
matches the driver.

Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 58230c2c443bc9801293f6535144d04ceaf731e0 upstream.

Caused by a copy & paste error. Note that even with
this bug AM437x SK display still works because GPIO
mux mode is always enabled. It's still wrong to mux
somebody else's pin.

Luckily ball D25 (offset 0x238 - gpio5_8) on AM437x
isn't used for anything.

While at that, also replace a pullup with a pulldown
as that gpio should be normally low, not high.

Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit ab1e85372168892387dd1ac171158fc8c3119be4 upstream.

Commit a095b1c78a35 ("ARM: mvebu: sort DT nodes by address")
missed placing the system-controller in the correct order.

Fixes: a095b1c78a35 ("ARM: mvebu: sort DT nodes by address")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/20141114204333.GS27002@pengutronix.de
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b4607572ef86b288a856b9df410ea593c5371dec upstream.

Back when audio was enabled, the muxing of some MPP pins was causing
problems. However, since commit fea038ed55ae ("ARM: mvebu: Add proper
pin muxing on the Armada 370 DB board"), those problematic MPP pins
have been assigned a proper muxing for the Ethernet interfaces. This
proper muxing is now conflicting with the hog pins muxing that had
been added as part of 249f3822509b ("ARM: mvebu: add audio support to
Armada 370 DB").

Therefore, this commit simply removes the hog pins muxing, which
solves a warning a boot time due to the conflicting muxing
requirements.

Fixes: fea038ed55ae ("ARM: mvebu: Add proper pin muxing on the Armada 370 DB board")
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1414512524-24466-5-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull "Samsung fixes for v3.18" from Kukjin Kim:

- explicitly set dr_mode on exynos5250-snow
  this is required when kernel is built with USB gadget support.

* tag 'samsung-fixes-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
  ARM: dts: Explicitly set dr_mode on exynos5250-snow

Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Pull "ARM: tegra: Device tree fixes for v3.18-rc5" from Thierry Reding:

This contains the serial port numbering fixes that are required for the
serial port numbering to stay the same with or without the serial core
making use of the aliases defined in DT.

eMMC is also fixed for TN7 and Roth boards which were using the wrong
regulators.

* tag 'tegra-for-3.18-fixes-for-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
  ARM: tegra: roth: Fix SD card VDD_IO regulator
  ARM: tegra: Remove eMMC vmmc property for roth/tn7
  ARM: dts: tegra: move serial aliases to per-board
  ARM: tegra: Add serial port labels to Tegra124 DT

Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Pull "Renesas ARM Based SoC DT Fixes for v3.18" from Simon Horman:

* Correct IIC0 parent clock on r8a7740
* Correct SD3CKCR address to device tree on r8a7790

* tag 'renesas-dt-fixes-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: shmobile: r8a7740 dtsi: Correct IIC0 parent clock
  ARM: shmobile: r8a7790: Fix SD3CKCR address to device tree

Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge "Allwinner fixes for 3.18" from Maxime Ripard:

A fix for the A31 dma controller that requires the AHB clock to be parented to
PLL6 in order to operate.

* tag 'sunxi-fixes-for-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
  ARM: dts: sun6i: Re-parent ahb1_mux to pll6 as required by dma controller

Signed-off-by: Arnd Bergmann <arnd@arndb.de>