Jonathan Cameron reports that when using the environment
variable KCONFIG_CONFIG, he encounters this error:

make[2]: *** No rule to make target `.config', needed by `arch/arm/boot/compressed/vmlinux.lds'

Reported-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Partially revert e69edc7, which introduced automatic zreladdr
support.  The change in the way the manual definition is defined
seems to be error and conflict prone.  Go back to the original way
we were handling this for the time being, while keeping the automatic
zreladdr facility.

Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Conflicts:
	arch/arm/Kconfig
	arch/arm/mm/Kconfig

"ARM: Auto calculate ZRELADDR and provide option for exceptions" broke
the Thumb-2 decompressor because it removed an entry in the LC0 table
but didn't adjust the offset the Thumb-2 code uses to load the SP from
that table.

Fix it, and also change the ARM code to use the separate SP-load since
ARM instructions that include the SP in the LDM register list are
deprecated.

Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Conflicts:
	arch/arm/mach-pxa/palmt5.c
	arch/arm/mach-pxa/palmtreo.c

With kexec-based kernel boot loader on Zaurus, the machine ID is
actually correctly passed, and head-sharpsl.S is not necessary.
Introduce PXA_SHARPSL_DETECT_MACH_ID, and include head-sharpsl.S
only when that's explicitly enabled.

Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (291 commits)
  ARM: AMBA: Add pclk support to AMBA bus infrastructure
  ARM: 6278/2: fix regression in RealView after the introduction of pclk
  ARM: 6277/1: mach-shmobile: Allow users to select HZ, default to 128
  ARM: 6276/1: mach-shmobile: remove duplicate NR_IRQS_LEGACY
  ARM: 6246/1: mmci: support larger MMCIDATALENGTH register
  ARM: 6245/1: mmci: enable hardware flow control on Ux500 variants
  ARM: 6244/1: mmci: add variant data and default MCICLOCK support
  ARM: 6243/1: mmci: pass power_mode to the translate_vdd callback
  ARM: 6274/1: add global control registers definition header file for nuc900
  mx2_camera: fix type of dma buffer virtual address pointer
  mx2_camera: Add soc_camera support for i.MX25/i.MX27
  arm/imx/gpio: add spinlock protection
  ARM: Add support for the LPC32XX arch
  ARM: LPC32XX: Arch config menu supoport and makefiles
  ARM: LPC32XX: Phytec 3250 platform support
  ARM: LPC32XX: Misc support functions
  ARM: LPC32XX: Serial support code
  ARM: LPC32XX: System suspend support
  ARM: LPC32XX: GPIO, timer, and IRQ drivers
  ARM: LPC32XX: Clock driver
  ...

Conflicts:
	arch/arm/kernel/entry-armv.S
	arch/arm/kernel/setup.c
	arch/arm/mm/init.c

Update the compressed boot Makefile for ARM to
remove files during clean.

Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

As long as the zImage is placed within the 128MB range from the start of
memory, ZRELADDR (Address where the decompressed kernel will be placed,
usually == PHYS_OFFSET + TEXT_OFFSET) can be determined at run-time by
masking PC with 0xf80000000.

Running through all the Makefile.boot, all those zreladdr-y
addresses == 0x[0-f][08]00_0000 + TEXT_OFFSET can be determined at
run-time.

Option CONFIG_AUTO_ZRELADDR and CONFIG_ZRELADDR are introduced,
CONFIG_ZRELADDR _must_ be explicitly specified if:

- ((zreladdr-y - TEXT_OFFSET) & ~0xf8000000) != 0, which means
  masking PC with 0xf8000000 will result in an incorrect address.
  Currently this is only a problem on u300.

- or the assumption of the zImage being loaded by the bootloader within
  the first 128MB of RAM is incorrect

- or when ZBOOT_ROM is used, where the above assumption is usually wrong.

[ukleinek: changed mask from 0xf0000000 to 0xf8000000 for mx1 and shark
+ some review fixes from the mailing list]

Original-Idea-and-Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Eric Miao <eric.miao@canonical.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>