* 'v3.3-samsung-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (2 commits) ARM: EXYNOS: Add cpu-offset property in gic device tree node ARM: EXYNOS: Bring exynos4-dt up to date Linux 3.3-rc3 This includes an update to the v3.3-rc3 release from v3.3-rc2 Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Commit db0d4db22a78 ('ARM: gic: allow GIC to support non-banked setups)
requires a cpu-offset property to be specified for non-banked gic
controllers, which is the case for Exynos4.
Reported-and-Tested-by: Karol Lewandowski <k.lewandowsk@samsung.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
UARTC is connected to the mini-pcie port. Signed-off-by: Marc Dietrich <marvin24@gmx.de> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Olof Johansson <olof@lixom.net>
The power gpio for the external memory card was specified wrongly. Replace it with the correct value (tested with warmboot with fastboot). Signed-off-by: Marc Dietrich <marvin24@gmx.de> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Olof Johansson <olof@lixom.net>
power management changes for omap and imx A significant part of the changes for these two platforms went into power management, so they are split out into a separate branch. * tag 'pm' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (65 commits) ARM: imx6: remove __CPUINIT annotation from v7_invalidate_l1 ARM: imx6: fix v7_invalidate_l1 by adding I-Cache invalidation ARM: imx6q: resume PL310 only when CACHE_L2X0 defined ARM: imx6q: build pm code only when CONFIG_PM selected ARM: mx5: use generic irq chip pm interface for pm functions on ARM: omap: pass minimal SoC/board data for UART from dt arm/dts: Add minimal device tree support for omap2420 and omap2430 omap-serial: Add minimal device tree support omap-serial: Use default clock speed (48Mhz) if not specified omap-serial: Get rid of all pdev->id usage ARM: OMAP2+: hwmod: Add a new flag to handle hwmods left enabled at init ARM: OMAP4: PRM: use PRCM interrupt handler ARM: OMAP3: pm: use prcm chain handler ARM: OMAP: hwmod: add support for selecting mpu_irq for each wakeup pad ARM: OMAP2+: mux: add support for PAD wakeup interrupts ARM: OMAP: PRCM: add suspend prepare / finish support ARM: OMAP: PRCM: add support for chain interrupt handler ARM: OMAP3/4: PRM: add functions to read pending IRQs, PRM barrier ARM: OMAP2+: hwmod: Add API to enable IO ring wakeup ARM: OMAP2+: mux: add wakeup-capable hwmod mux entries to dynamic list ...
Driver specific changes Again, a lot of platforms have changes in here: pxa, samsung, omap, at91, imx, ... * tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits) ARM: sa1100: clean up of the clock support ARM: pxa: add dummy clock for sa1100-rtc RTC: sa1100: support sa1100, pxa and mmp soc families RTC: sa1100: remove redundant code of setting alarm RTC: sa1100: Clean out ost register Input: zylonite-wm97xx - replace IRQ_GPIO() with gpio_to_irq() pcmcia: pxa: replace IRQ_GPIO() with gpio_to_irq() ARM: EXYNOS: Modified files for SPI consolidation work ARM: S5P64X0: Enable SDHCI support ARM: S5P64X0: Add lookup of sdhci-s3c clocks using generic names ARM: S5P64X0: Add HSMMC setup for host Controller ARM: EXYNOS: Add USB OHCI support to ORIGEN board USB: Add Samsung Exynos OHCI diver ARM: EXYNOS: Add USB OHCI support to SMDKV310 board ARM: EXYNOS: Add USB OHCI device net: macb: fix build break with !CONFIG_OF i2c: tegra: Support DVC controller in device tree i2c: tegra: Add __devinit/exit to probe/remove net/at91_ether: use gpio_is_valid for phy IRQ line ARM: at91/net: add macb ethernet controller in 9g45/9g20 DT ...
New feature development This adds support for new features, and contains stuff from most platforms. A number of these patches could have fit into other branches, too, but were small enough not to cause too much confusion here. * tag 'devel' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits) mfd/db8500-prcmu: remove support for early silicon revisions ARM: ux500: fix the smp_twd clock calculation ARM: ux500: remove support for early silicon revisions ARM: ux500: update register files ARM: ux500: register DB5500 PMU dynamically ARM: ux500: update ASIC detection for U5500 ARM: ux500: support DB8520 ARM: picoxcell: implement watchdog restart ARM: OMAP3+: hwmod data: Add the default clockactivity for I2C ARM: OMAP3: hwmod data: disable multiblock reads on MMC1/2 on OMAP34xx/35xx <= ES2.1 ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP4 ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP3 ARM: OMAP: hwmod data: Add support for AM35xx UART4/ttyO3 ARM: Orion: Remove address map info from all platform data structures ARM: Orion: Get address map from plat-orion instead of via platform_data ARM: Orion: mbus_dram_info consolidation ARM: Orion: Consolidate the address map setup ARM: Kirkwood: Add configuration for MPP12 as GPIO ARM: Kirkwood: Recognize A1 revision of 6282 chip ARM: ux500: update the MOP500 GPIO assignments ...
Board-level changes This adds and extends support for specific boards on a number of ARM platforms: omap, imx, samsung, tegra, ... * tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (49 commits) Enable 32 bit flash support for iMX21ADS board ARM: mx31pdk: Add MC13783 RTC support iomux-mx25: configuration to support CSPI3 on CSI pins MX1:apf9328: Add i2c support mioa701: add newly available DoC G3 chip arm/tegra: remove __initdata annotation from pinmux tables arm/tegra: Use bus notifiers to trigger pinmux setup arm/tegra: Refactor board-*-pinmux.c to share code arm/tegra: Fix mistake in Trimslice's pinmux arm/tegra: Rework Seaboard-vs-Ventana pinmux table arm/tegra: Remove useless entries from ventana_pinmux[] arm/tegra: PCIe: Remove include of mach/pinmux.h arm/tegra: Harmony PCIe: Don't touch pinmux arm/tegra: Add AUXDATA for tegra-pinmux and tegra-gpio arm/tegra: Split Seaboard GPIO table to allow for Ventana ARM: imx6q: generate imx6q dtb files arm/imx6q: Rename Sabreauto to Armadillo2 arm/imx6q-sabrelite: add enet phy ksz9021rn fixup arm/imx6: add imx6q sabrelite board support dts/imx: rename uart labels to consistent with hw spec ...
SoC-level changes for tegra and omap This adds support for the new tegra30 SoC, as well as small changes to support minor variations of existing omap SoCs. * tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (26 commits) arm/tegra: Compile tegra_dt_init_irq only when CONFIG_OF arm/tegra: Make MACH_TEGRA_DT depend on ARCH_TEGRA_2x_SOC arm/tegra: Delete tegra_init_clock() arm/tegra: Fix section mismatch errors in tegra30 pinmux arm/tegra: Fix section mismatch errors in tegra20 pinmux arm/tegra: refresh defconfig for tegra30 arm/tegra: add support for tegra30 based board cardhu arm/tegra: implement support for tegra30 arm/tegra: pinmux tables and definitions for tegra30 arm/tegra: add new fields to struct tegra_pingroup_desc arm/tegra: prepare pinmux code for multiple tegra variants arm/tegra: rename tegra20 pinmux files arm/tegra: generalize L2 cache initialization arm/tegra: use PMC reset arm/tegra: rename board-dt.c to board-dt-tegra20.c arm/tegra: prepare early init for multiple tegra variants arm/tegra: don't export clk_measure_input_freq arm/tegra: prepare clock code for multiple tegra variants arm/tegra: cleanup tegra20 support arm/tegra: clk_get should not be fatal ... Fix up trivial conflict in arch/arm/mach-tegra/board-dt-tegra20.c
Device tree conversions for samsung and tegra Both platforms had some initial device tree support, but this adds much more to actually make it usable. * tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (45 commits) ARM: dts: Add intial dts file for EXYNOS4210 SoC, SMDKV310 and ORIGEN ARM: EXYNOS: Add Exynos4 device tree enabled board file rtc: rtc-s3c: Add device tree support input: samsung-keypad: Add device tree support ARM: S5PV210: Modify platform data for pl330 driver ARM: S5PC100: Modify platform data for pl330 driver ARM: S5P64x0: Modify platform data for pl330 driver ARM: EXYNOS: Add a alias for pdma clocks ARM: EXYNOS: Limit usage of pl330 device instance to non-dt build ARM: SAMSUNG: Add device tree support for pl330 dma engine wrappers DMA: PL330: Add device tree support ARM: EXYNOS: Modify platform data for pl330 driver DMA: PL330: Infer transfer direction from transfer request instead of platform data DMA: PL330: move filter function into driver serial: samsung: Fix build for non-Exynos4210 devices serial: samsung: add device tree support serial: samsung: merge probe() function from all SoC specific extensions serial: samsung: merge all SoC specific port reset functions ARM: SAMSUNG: register uart clocks to clock lookup list serial: samsung: remove all uses of get_clksrc and set_clksrc ... Fix up fairly trivial conflicts in arch/arm/mach-s3c2440/clock.c and drivers/tty/serial/Kconfig both due to just adding code close to changes.