[ Upstream commit f6628486c8489e91c513b62608f89ccdb745600d ]

Cyclone5 and Arria10 doesn't have the same memory map for UART1.

Split the SOCFPGA_UART1 into 2 options to allow debugging on UART1 for Cyclone5.

Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 7c41ea57beb2aee96fa63091a457b1a2826f3c42 ]

If debugging on i.MX is enabled DEBUG_IMX_UART_PORT defines which UART
is used for the debug output. If however debugging is off don't only
hide the then unused config item but drop it completely by using a
dependency instead of a conditional prompt.

This fixes DEBUG_IMX_UART_PORT being present in the kernel config even
if DEBUG_LL is disabled.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Pull "Renesas ARM Based SoC Updates for v4.9" from Simon Horman:

Clean-up:
* Only use smp_init when SMP is selected

Enablement:
* Add debug-ll support for r8a7992

* tag 'renesas-soc-for-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: shmobile: r8a7791: only use smp_init when SMP is selected
  ARM: shmobile: r8a7790: only use smp_init when SMP is selected
  ARM: debug-ll: Add support for r8a7992

Enable low-level debugging support for R-Car V2H (r8a7792).
V2H uses SCIF0 for the debug console, like most other R-Car Gen2 SoCs.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The SUN_TOP_CTRL_FAMILY_ID register  is at a fixed absolute address for
all of our supported chips, so utilize its value to determine what the
UARTA base address should be based on the value we read.

Since the code is called both during decompressor when the MMU is off,
and after the MMU has been turned on in the kernel, and we want to do
the lookup only once, we use the same technique as tegra.S and have a
shared storage location between the decompressor and the kernel.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Merge "the second part of the Broadcom ARM-based SoC changes" from Florian Fainelli:

- Florian updates the DEBUG_UART_BCM5301X entry to cover both NS and NSP SoCs
  since they both have the same location

* tag 'arm-soc/for-4.8/soc-part2' of http://github.com/Broadcom/stblinux:
  ARM: debug: Enable DEBUG_BCM_5301X for Northstar Plus SoCs

Northstar Plus SoCs (ARCH_BCM_NSP) have the exact same UART location and
properties like the register shift of 0, so make it usable.

Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Add configuration options for the most commonly used UART physical and
virtual addresses to ease the use of DEBUG_LL and earlyprintk.

Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

AT91 still uses an offset (0x0100 0000) from the physical address to map
the debug UART. This is unfortunate as for some platforms (sama5d3 and
earlier), it ends up in the PCI zone and PCI is enabled in multi_v7.
Switch to DEBUG_UART_VIRT to solve that.

Tested on sama5d3 and 9g20.

Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

DEBUG_HI3716_UART was supposed to be renamed to DEBUG_HIX5HD2_UART, but
accidentally both got left in place, which results in a build error when
CONFIG_DEBUG_UART_PHYS is not set as it should be.

This removes the old symbol.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 12aae3097454 ("ARM: debug: Rename Hi3716 to HIX5HD2")
Acked-by: Wei Xu <xuwei5@hisilicon.com>