[ Upstream commit aee123f48f387ea62002cddb46c7cb04c96628df ] Remove "ti,dma-ring-reset-quirk" DT property as proper w/a handling is implemented now in Ringacc driver using SoC info. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 884d1a334ae8130fabede56f59b224619ad6bca4 ]
When adding allwinner,sun8i-a33-crypto, I forgot to add that it needs reset.
Furthermore, there are no need to use items to list only one compatible
in compatible list.
Fixes: f81547ba7a98 ("dt-bindings: crypto: add new compatible for A33 SS")
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200907175437.4464-1-clabbe.montjoie@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit acd7aaf51b20263a7e62d2a26569988c63bdd3d8 ]
Since commit bbc4d71d63549bc ("net: phy: realtek: fix rtl8211e rx/tx
delay config"), the Realtek PHY driver will override any TX/RX delay
set by hardware straps if the phy-mode device property does not match.
This is causing problems on SynQuacer based platforms (the only SoC
that incorporates the netsec hardware), since many were built with
this Realtek PHY, and shipped with firmware that defines the phy-mode
as 'rgmii', even though the PHY is configured for TX and RX delay using
pull-ups.
>From the driver's perspective, we should not make any assumptions in
the general case that the PHY hardware does not require any initial
configuration. However, the situation is slightly different for ACPI
boot, since it implies rich firmware with AML abstractions to handle
hardware details that are not exposed to the OS. So in the ACPI case,
it is reasonable to assume that the PHY comes up in the right mode,
regardless of whether the mode is set by straps, by boot time firmware
or by AML executed by the ACPI interpreter.
So let's ignore the 'phy-mode' device property when probing the netsec
driver in ACPI mode, and hardcode the mode to PHY_INTERFACE_MODE_NA,
which should work with any PHY provided that it is configured by the
time the driver attaches to it. While at it, document that omitting
the mode is permitted for DT probing as well, by setting the phy-mode
DT property to the empty string.
Fixes: 533dd11a12f6 ("net: socionext: Add Synquacer NetSec driver")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201018163625.2392-1-ardb@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull networking fixes from David Miller:
1) Make sure SKB control block is in the proper state during IPSEC
ESP-in-TCP encapsulation. From Sabrina Dubroca.
2) Various kinds of attributes were not being cloned properly when we
build new xfrm_state objects from existing ones. Fix from Antony
Antony.
3) Make sure to keep BTF sections, from Tony Ambardar.
4) TX DMA channels need proper locking in lantiq driver, from Hauke
Mehrtens.
5) Honour route MTU during forwarding, always. From Maciej
Żenczykowski.
6) Fix races in kTLS which can result in crashes, from Rohit
Maheshwari.
7) Skip TCP DSACKs with rediculous sequence ranges, from Priyaranjan
Jha.
8) Use correct address family in xfrm state lookups, from Herbert Xu.
9) A bridge FDB flush should not clear out user managed fdb entries
with the ext_learn flag set, from Nikolay Aleksandrov.
10) Fix nested locking of netdev address lists, from Taehee Yoo.
11) Fix handling of 32-bit DATA_FIN values in mptcp, from Mat Martineau.
12) Fix r8169 data corruptions on RTL8402 chips, from Heiner Kallweit.
13) Don't free command entries in mlx5 while comp handler could still be
running, from Eran Ben Elisha.
14) Error flow of request_irq() in mlx5 is busted, due to an off by one
we try to free and IRQ never allocated. From Maor Gottlieb.
15) Fix leak when dumping netlink policies, from Johannes Berg.
16) Sendpage cannot be performed when a page is a slab page, or the page
count is < 1. Some subsystems such as nvme were doing so. Create a
"sendpage_ok()" helper and use it as needed, from Coly Li.
17) Don't leak request socket when using syncookes with mptcp, from
Paolo Abeni.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (111 commits)
net/core: check length before updating Ethertype in skb_mpls_{push,pop}
net: mvneta: fix double free of txq->buf
net_sched: check error pointer in tcf_dump_walker()
net: team: fix memory leak in __team_options_register
net: typhoon: Fix a typo Typoon --> Typhoon
net: hinic: fix DEVLINK build errors
net: stmmac: Modify configuration method of EEE timers
tcp: fix syn cookied MPTCP request socket leak
libceph: use sendpage_ok() in ceph_tcp_sendpage()
scsi: libiscsi: use sendpage_ok() in iscsi_tcp_segment_map()
drbd: code cleanup by using sendpage_ok() to check page for kernel_sendpage()
tcp: use sendpage_ok() to detect misused .sendpage
nvme-tcp: check page by sendpage_ok() before calling kernel_sendpage()
net: add WARN_ONCE in kernel_sendpage() for improper zero-copy send
net: introduce helper sendpage_ok() in include/linux/net.h
net: usb: pegasus: Proper error handing when setting pegasus' MAC address
net: core: document two new elements of struct net_device
netlink: fix policy dump leak
net/mlx5e: Fix race condition on nhe->n pointer in neigh update
net/mlx5e: Fix VLAN create flow
...
Pull GPIO fixes from Linus Walleij:
"Some late GPIO fixes for the v5.9 series:
- Fix compiler warnings on the OMAP when PM is disabled
- Clear the interrupt when setting edge sensitivity on the Spreadtrum
driver.
- Fix up spurious interrupts on the TC35894.
- Support threaded interrupts on the Siox controller.
- Fix resource leaks on the mockup driver.
- Fix line event handling in syscall compatible mode for the
character device.
- Fix an unitialized variable in the PCA953A driver.
- Fix access to all GPIO IRQs on the Aspeed AST2600.
- Fix line direction on the AMD FCH driver.
- Use the bitmap API instead of compiler intrinsics for bit
manipulation in the PCA953x driver"
* tag 'gpio-v5.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: pca953x: Correctly initialize registers 6 and 7 for PCA957x
gpio: pca953x: Use bitmap API over implicit GCC extension
gpio: amd-fch: correct logic of GPIO_LINE_DIRECTION
gpio: aspeed: fix ast2600 bank properties
gpio/aspeed-sgpio: don't enable all interrupts by default
gpio/aspeed-sgpio: enable access to all 80 input & output sgpios
gpio: pca953x: Fix uninitialized pending variable
gpiolib: Fix line event handling in syscall compatible mode
gpio: mockup: fix resource leak in error path
gpio: siox: explicitly support only threaded irqs
gpio: tc35894: fix up tc35894 interrupt configuration
gpio: sprd: Clear interrupt when setting the type as edge
gpio: omap: Fix warnings if PM is disabled
Pull devicetree fixes from Rob Herring: - Fix handling of HOST_EXTRACFLAGS for dtc - Several warning fixes for DT bindings * tag 'devicetree-fixes-for-5.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: scripts/dtc: only append to HOST_EXTRACFLAGS instead of overwriting dt-bindings: Fix 'reg' size issues in zynqmp examples ARM: dts: bcm2835: Change firmware compatible from simple-bus to simple-mfd dt-bindings: leds: cznic,turris-omnia-leds: fix error in binding dt-bindings: crypto: sa2ul: fix a DT binding check warning
The default sizes in examples for 'reg' are 1 cell each. Fix the incorrect sizes in zynqmp examples: Documentation/devicetree/bindings/dma/xilinx/xlnx,zynqmp-dpdma.example.dt.yaml: example-0: dma-controller@fd4c0000:reg:0: [0, 4249616384, 0, 4096] is too long From schema: /usr/local/lib/python3.8/dist-packages/dtschema/schemas/reg.yaml Documentation/devicetree/bindings/display/xlnx/xlnx,zynqmp-dpsub.example.dt.yaml: example-0: display@fd4a0000:reg:0: [0, 4249485312, 0, 4096] is too long From schema: /usr/local/lib/python3.8/dist-packages/dtschema/schemas/reg.yaml Documentation/devicetree/bindings/display/xlnx/xlnx,zynqmp-dpsub.example.dt.yaml: example-0: display@fd4a0000:reg:1: [0, 4249526272, 0, 4096] is too long From schema: /usr/local/lib/python3.8/dist-packages/dtschema/schemas/reg.yaml Documentation/devicetree/bindings/display/xlnx/xlnx,zynqmp-dpsub.example.dt.yaml: example-0: display@fd4a0000:reg:2: [0, 4249530368, 0, 4096] is too long From schema: /usr/local/lib/python3.8/dist-packages/dtschema/schemas/reg.yaml Documentation/devicetree/bindings/display/xlnx/xlnx,zynqmp-dpsub.example.dt.yaml: example-0: display@fd4a0000:reg:3: [0, 4249534464, 0, 4096] is too long From schema: /usr/local/lib/python3.8/dist-packages/dtschema/schemas/reg.yaml Cc: Hyun Kwon <hyun.kwon@xilinx.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Vinod Koul <vkoul@kernel.org> Cc: dri-devel@lists.freedesktop.org Cc: dmaengine@vger.kernel.org Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Rob Herring <robh@kernel.org>
gpio: fixes for v5.9-rc7 - fix uninitialized variable in gpio-pca953x - enable all 160 lines and fix interrupt configuration in gpio-aspeed-gpio - fix ast2600 bank properties in gpio-aspeed
The current binding for the RPi firmware uses the simple-bus compatible as a fallback to benefit from its automatic probing of child nodes. However, simple-bus also comes with some constraints, like having the ranges, our case. Let's switch to simple-mfd that provides the same probing logic without those constraints. Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://lore.kernel.org/r/20200924082642.18144-1-maxime@cerno.tech Signed-off-by: Rob Herring <robh@kernel.org>
Document RZ/G2H (R8A774E1) SoC bindings. Signed-off-by: Marian-Cristian Rotariu <marian-cristian.rotariu.rb@bp.renesas.com> Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>