Pull ARM SoC-specific updates from Arnd Bergmann:
 "This is a larger set of new functionality for the existing SoC
  families, including:

   - vt8500 gains support for new CPU cores, notably the Cortex-A9 based
     wm8850

   - prima2 gains support for the "marco" SoC family, its SMP based
     cousin

   - tegra gains support for the new Tegra4 (Tegra114) family

   - socfpga now supports a newer version of the hardware including SMP

   - i.mx31 and bcm2835 are now using DT probing for their clocks

   - lots of updates for sh-mobile

   - OMAP updates for clocks, power management and USB

   - i.mx6q and tegra now support cpuidle

   - kirkwood now supports PCIe hot plugging

   - tegra clock support is updated

   - tegra USB PHY probing gets implemented diffently"

* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (148 commits)
  ARM: prima2: remove duplicate v7_invalidate_l1
  ARM: shmobile: r8a7779: Correct TMU clock support again
  ARM: prima2: fix __init section for cpu hotplug
  ARM: OMAP: Consolidate OMAP USB-HS platform data (part 3/3)
  ARM: OMAP: Consolidate OMAP USB-HS platform data (part 1/3)
  arm: socfpga: Add SMP support for actual socfpga harware
  arm: Add v7_invalidate_l1 to cache-v7.S
  arm: socfpga: Add entries to enable make dtbs socfpga
  arm: socfpga: Add new device tree source for actual socfpga HW
  ARM: tegra: sort Kconfig selects for Tegra114
  ARM: tegra: enable ARCH_REQUIRE_GPIOLIB for Tegra114
  ARM: tegra: Fix build error w/ ARCH_TEGRA_114_SOC w/o ARCH_TEGRA_3x_SOC
  ARM: tegra: Fix build error for gic update
  ARM: tegra: remove empty tegra_smp_init_cpus()
  ARM: shmobile: Register ARM architected timer
  ARM: MARCO: fix the build issue due to gic-vic-to-irqchip move
  ARM: shmobile: r8a7779: Correct TMU clock support
  ARM: mxs_defconfig: Select CONFIG_DEVTMPFS_MOUNT
  ARM: mxs: decrease mxs_clockevent_device.min_delta_ns to 2 clock cycles
  ARM: mxs: use apbx bus clock to drive the timers on timrotv2
  ...

As reset GPIO information is PHY specific detail, adding
it to PHY DT node.

Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Add DT nodes for Tegra USB PHY along with related documentation.
Also added a phandle property to controller DT node, for referring
to connected PHY instance.

Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

As Tegra USB host driver is using instance number for resetting
PORT0 twice, adding a new DT property for handling this.

Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Stephen Warren <swarren@nvidia.com>

Felipe writes:
	usb: xceiv: patches for v3.9 merge window

	Two new PHY drivers coming here: one for Samsung,
	one for OMAP. Both architectures are adding USB3
	support to mainline kernel.

	The PHY layer now allows us to have mulitple PHYs
	of the same type, which is necessary for platforms
	which provide more than one USB peripheral port.

	There's also a few cleanups here: removal of __dev*
	annotations, conversion of a cast to to_delayed_work(),
	and mxs-phy learns about ->set_suspend.

Added dt support for dwc3 core and update the documentation with
device tree binding information. Getting a PHY is now done using
devm_usb_get_phy_by_phandle() for dt boot.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Added a driver for usb3 phy that handles the interaction between usb phy
device and dwc3 controller.

This also includes device tree support for usb3 phy driver and
the documentation with device tree binding information is updated.

Currently writing to control module register is taken care in this
driver which will be removed once the control module driver is in place.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Start using the control module driver for powering on the PHY and for
writing to the mailbox instead of writing to the control module
registers on their own.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Added a new driver for the usb part of control module. This has an API
to power on the USB2 phy and an API to write to the mailbox depending on
whether MUSB has to act in host mode or in device mode.

Writing to control module registers for doing the above task which was
previously done in omap glue and in omap-usb2 phy will be removed.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Added device tree support for usb3503 driver and add new document with device tree binding information.

Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>