Pull ARM soc device tree updates from Olof Johansson:
 "Device tree conversion and enablement branch.  Mostly a bunch of new
  bindings and setup for various platforms, but the Via/Winchip VT8500
  platform is also converted over from being 100% legacy to now use
  device tree for probing.  More of that will come for 3.8."

Trivial conflicts due to removal of vt8500 files, and one documentation
file that was added with slightly different contents both here and in
the USb tree.

* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (212 commits)
  arm: vt8500: Fixup for missing gpio.h
  ARM: LPC32xx: LED fix in PHY3250 DTS file
  ARM: dt: mmp-dma: add binding file
  arm: vt8500: Update arch-vt8500 to devicetree support.
  arm: vt8500: gpio: Devicetree support for arch-vt8500
  arm: vt8500: doc: Add device tree bindings for arch-vt8500 devices
  arm: vt8500: clk: Add Common Clock Framework support
  video: vt8500: Add devicetree support for vt8500-fb and wm8505-fb
  serial: vt8500: Add devicetree support for vt8500-serial
  rtc: vt8500: Add devicetree support for vt8500-rtc
  arm: vt8500: Add device tree files for VIA/Wondermedia SoC's
  ARM: tegra: Add Avionic Design Tamonten Evaluation Carrier support
  ARM: tegra: Add Avionic Design Medcom-Wide support
  ARM: tegra: Add Avionic Design Plutux support
  ARM: tegra: Add Avionic Design Tamonten support
  ARM: tegra: dts: Add pwm label
  ARM: ux500: Fix SSP register address format
  ARM: ux500: Apply tc3589x's GPIO/IRQ properties to HREF's DT
  ARM: ux500: Remove redundant #gpio-cell properties from Snowball DT
  ARM: ux500: Add all encompassing sound node to the HREF Device Tree
  ...

Bindings for gpio, interrupt controller, power management controller,
timer, realtime clock, serial uart, ehci and uhci controllers and
framebuffer controllers used on the arch-vt8500 platform.

Framebuffer binding also specifies a 'display' node which is required
for determining the lcd panel data.

Signed-off-by: Tony Prisk <linux@prisktech.co.nz>

i.MX usb controllers share non-core registers, which may include
SoC specific controls. We turn it into a usbmisc device and usbmisc
driver set operations needed by ci13xxx_imx driver.

For example, Sabrelite board has bad over-current design, we can
usbmisc to disable over-current detection.

Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: musb: patches for v3.7 merge window

Here we have a bunch of miscellaneous cleanups and fixes
to the musb driver. It fixes a bunch of mistakes errors
which nobody has triggered before, so I'm not Ccing stable
tree.

We are finally improving OMAP's VBUS/ID Mailbox usage so
that we can introduce our PHY drivers properly. Also, we're
adding support for multiple instances of the MUSB IP in
the same SoC, as seen on some platforms from TI which
have 2 MUSB instances.

Other than that, we have some small fixes like not kicking
DMA for a zero byte transfer, or properly handling NAK timeout
on MUSB's host side, and the enabling of DMA Mode1 for any
transfers which are aligned to wMaxPacketSize.

All patches have been pending on mailing list for a long time
and I don't expect any big surprises with this pull request.

usb: xceiv: patches for v3.7 merge window

nop xceiv got its own header to avoid polluting otg.h. It has also
learned to work as USB2 and USB3 phys so we can use it on USB3
controllers.

Together with those two changes to nop xceiv, we're adding basic
PHY support to dwc3 driver, this is to allow platforms which actually
have a SW-controllable PHY talk to them through dwc3 driver.

We're adding a new phy driver for the OMAP architecture. This driver
is for the PHY found in OMAP4 SoCs, and a new phy driver for the
marvell architecture. An extra phy driver - for Tegra SoCs - is now
moving from arch/arm/mach-tegra* to drivers/usb/phy.

Also here, there's the creation of <linux/usb/phy.h> which should be
used from now on for PHY drivers, even those which don't support
OTG.

Added device tree support for dsps musb glue driver and updated the
Documentation with device tree binding information.

Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Santhapuri, Damodar <damodar.santhapuri@ti.com>
Signed-off-by: Ravi Babu <ravibabu@ti.com>
[afzal@ti.com: use '-' instead of '_' for dt properties]
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Added device tree support for omap musb driver and updated the
Documentation with device tree binding information.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Add device tree support for twl4030 usb driver.
Update the Documentation with device tree binding information.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Add device tree support for twl6030 usb driver.
Update the Documentation with device tree binding information.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

All phy related programming like enabling/disabling the clocks, powering
on/off the phy is taken care of by this driver. It is also used for OTG
related functionality like srp.

This also includes device tree support for usb2 phy driver and
the documentation with device tree binding information is updated.

Currently writing to control module register is taken care in this
driver which will be removed once the control module driver is in place.

Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>