linux-stable.git/Documentation/devicetree/bindings/net, branch linux-4.20.y Linux kernel stable tree dt-bindings: dsa: Fix typo in "probed" 2018-11-24T06:33:55+00:00 Fabio Estevam festevam@gmail.com 2018-11-23T17:46:50+00:00 e7b9fb4f545b1f7885e7c642643828f93d3d79c9 The correct form is "can be probed", so fix the typo. Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> 
The correct form is "can be probed", so fix the typo.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
can: hi311x: Use level-triggered interrupt 2018-11-09T16:20:08+00:00 Lukas Wunner lukas@wunner.de 2018-10-27T08:36:54+00:00 f164d0204b1156a7e0d8d1622c1a8d25752befec If the hi3110 shares the SPI bus with another traffic-intensive device and packets are received in high volume (by a separate machine sending with "cangen -g 0 -i -x"), reception stops after a few minutes and the counter in /proc/interrupts stops incrementing. Bus state is "active". Bringing the interface down and back up reconvenes the reception. The issue is not observed when the hi3110 is the sole device on the SPI bus. Using a level-triggered interrupt makes the issue go away and lets the hi3110 successfully receive 2 GByte over the course of 5 days while a ks8851 Ethernet chip on the same SPI bus handles 6 GByte of traffic. Unfortunately the hi3110 datasheet is mum on the trigger type. The pin description on page 3 only specifies the polarity (active high): http://www.holtic.com/documents/371-hi-3110_v-rev-kpdf.do Cc: Mathias Duckeck <m.duckeck@kunbus.de> Cc: Akshay Bhat <akshay.bhat@timesys.com> Cc: Casey Fitzpatrick <casey.fitzpatrick@timesys.com> Signed-off-by: Lukas Wunner <lukas@wunner.de> Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> 
If the hi3110 shares the SPI bus with another traffic-intensive device
and packets are received in high volume (by a separate machine sending
with "cangen -g 0 -i -x"), reception stops after a few minutes and the
counter in /proc/interrupts stops incrementing.  Bus state is "active".
Bringing the interface down and back up reconvenes the reception.  The
issue is not observed when the hi3110 is the sole device on the SPI bus.

Using a level-triggered interrupt makes the issue go away and lets the
hi3110 successfully receive 2 GByte over the course of 5 days while a
ks8851 Ethernet chip on the same SPI bus handles 6 GByte of traffic.

Unfortunately the hi3110 datasheet is mum on the trigger type.  The pin
description on page 3 only specifies the polarity (active high):
http://www.holtic.com/documents/371-hi-3110_v-rev-kpdf.do

Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Cc: Akshay Bhat <akshay.bhat@timesys.com>
Cc: Casey Fitzpatrick <casey.fitzpatrick@timesys.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
dt-bindings: can: rcar_can: Add r8a774a1 support 2018-11-09T16:20:08+00:00 Fabrizio Castro fabrizio.castro@bp.renesas.com 2018-09-10T10:43:14+00:00 868b7c0f43e61f227bf3d7f7d6134bb3c67bb0e8 Document RZ/G2M (r8a774a1) SoC specific bindings. Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com> Signed-off-by: Chris Paterson <Chris.Paterson2@renesas.com> Reviewed-by: Biju Das <biju.das@bp.renesas.com> Reviewed-by: Rob Herring <robh@kernel.org> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> 
Document RZ/G2M (r8a774a1) SoC specific bindings.

Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Chris Paterson <Chris.Paterson2@renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
dt-bindings: can: rcar_can: document r8a77965 support 2018-11-09T16:20:08+00:00 Eugeniu Rosca rosca.eugeniu@gmail.com 2018-08-20T14:49:10+00:00 4f145f14f6b98b5aa0dd91bdae518b3f24f74b37 Document the support for rcar_can on R8A77965 SoC devices. Add R8A77965 to the list of SoCs which require the "assigned-clocks" and "assigned-clock-rates" properties (thanks, Sergei). Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> 
Document the support for rcar_can on R8A77965 SoC devices.
Add R8A77965 to the list of SoCs which require the "assigned-clocks" and
"assigned-clock-rates" properties (thanks, Sergei).

Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc 2018-10-29T22:37:33+00:00 Linus Torvalds torvalds@linux-foundation.org 2018-10-29T22:37:33+00:00 4b42745211af552f170f38a1b97f4a112b5da6b2 Pull ARM SoC platform updates from Arnd Bergmann: "A couple of platforms change hands in the MAINTAINERS file: - Linus Walleij lists himself for the ARM Reference platforms: versatile, vexpress, integrator and realview. He has been the main contributor for these for a while, and makes it official now. - Vladimir Zapolskiy takes over the LPC18xx platform from Joachim Eastwood - Manivannan Sadhasivam becomes a secondary maintainer for the Actions Semi machines - Nicolas Ferre lists updates the MAINTAINER listing for the AT91 platform: Ludovic Desroches is now a co-maintainer for the platform, and several other people (Claudiu Beznea, Cristian Birsan, Eugen Hristev, Codrin Ciubotariu) take over individual device drivers. Thanks everyone for working on this, and welcome to the new maintainers! The "virt" platform on qemy or kvm can now be used in big-endian mode without additional tricks, thanks to Jason Donenfeld. Once again, we gain support for another NXP i.MX6 variant, this time it's the i.MX 6ULZ 32-bit single-core version. On arm64, we add support for two SoCs from Renesas: RZ/G2E (r8a774c0) and RZ/G2M (r8a774a1). These are described as microcontrollers on the manufacturer website, but appear to be rather powerful. The RZ/G2M is used on the reference board for the CIP Super Long Term Support (SLTS) Linux Kernels" * tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits) MAINTAINERS: Assign myself as a maintainer of ARM/LPC18XX architecture arm64: exynos: Enable generic power domain support MAINTAINERS: remove non-exsiting email address of Baoyou MAINTAINERS: fix pattern in ARM/Synaptics berlin SoC section MAINTAINERS: Drop dt-bindings/genpd/k2g.h ARM: samsung: Limit SAMSUNG_PM_CHECK config option to non-Exynos platforms arm64: actions: Enable PINCTRL in platforms Kconfig MAINTAINERS: Add entry for Actions Semi Owl SoCs DMA driver MAINTAINERS: Add entry for Actions Semiconductor Owl I2C driver MAINTAINERS: Update clock binding entry for Actions Semi Owl SoCs ARM: imx: add i.mx6ulz msl support ARM: Assume maintainership of ARM reference designs ARM: support big-endian for the virt architecture MAINTAINERS: sdhci: move the Microchip entry to proper location MAINTAINERS: move former ATMEL entries to proper MICROCHIP location MAINTAINERS: remove the / ATMEL string from MICROCHIP entries MAINTAINERS: iio: add co-maintainer to SAMA5D2-compatible ADC driver MAINTAINERS: pwm: add entry for Microchip pwm driver MAINTAINERS: dmaengine: add files to Microchip dma entry MAINTAINERS: USB: change maintainer for Microchip USBA gadget driver ... 
Pull ARM SoC platform updates from Arnd Bergmann:
 "A couple of platforms change hands in the MAINTAINERS file:

   - Linus Walleij lists himself for the ARM Reference platforms:
     versatile, vexpress, integrator and realview. He has been the main
     contributor for these for a while, and makes it official now.

   - Vladimir Zapolskiy takes over the LPC18xx platform from Joachim
     Eastwood

   - Manivannan Sadhasivam becomes a secondary maintainer for the
     Actions Semi machines

   - Nicolas Ferre lists updates the MAINTAINER listing for the AT91
     platform: Ludovic Desroches is now a co-maintainer for the
     platform, and several other people (Claudiu Beznea, Cristian
     Birsan, Eugen Hristev, Codrin Ciubotariu) take over individual
     device drivers.

  Thanks everyone for working on this, and welcome to the new
  maintainers!

  The "virt" platform on qemy or kvm can now be used in big-endian mode
  without additional tricks, thanks to Jason Donenfeld.

  Once again, we gain support for another NXP i.MX6 variant, this time
  it's the i.MX 6ULZ 32-bit single-core version.

  On arm64, we add support for two SoCs from Renesas: RZ/G2E (r8a774c0)
  and RZ/G2M (r8a774a1). These are described as microcontrollers on the
  manufacturer website, but appear to be rather powerful. The RZ/G2M is
  used on the reference board for the CIP Super Long Term Support (SLTS)
  Linux Kernels"

* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
  MAINTAINERS: Assign myself as a maintainer of ARM/LPC18XX architecture
  arm64: exynos: Enable generic power domain support
  MAINTAINERS: remove non-exsiting email address of Baoyou
  MAINTAINERS: fix pattern in ARM/Synaptics berlin SoC section
  MAINTAINERS: Drop dt-bindings/genpd/k2g.h
  ARM: samsung: Limit SAMSUNG_PM_CHECK config option to non-Exynos platforms
  arm64: actions: Enable PINCTRL in platforms Kconfig
  MAINTAINERS: Add entry for Actions Semi Owl SoCs DMA driver
  MAINTAINERS: Add entry for Actions Semiconductor Owl I2C driver
  MAINTAINERS: Update clock binding entry for Actions Semi Owl SoCs
  ARM: imx: add i.mx6ulz msl support
  ARM: Assume maintainership of ARM reference designs
  ARM: support big-endian for the virt architecture
  MAINTAINERS: sdhci: move the Microchip entry to proper location
  MAINTAINERS: move former ATMEL entries to proper MICROCHIP location
  MAINTAINERS: remove the / ATMEL string from MICROCHIP entries
  MAINTAINERS: iio: add co-maintainer to SAMA5D2-compatible ADC driver
  MAINTAINERS: pwm: add entry for Microchip pwm driver
  MAINTAINERS: dmaengine: add files to Microchip dma entry
  MAINTAINERS: USB: change maintainer for Microchip USBA gadget driver
  ...
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc 2018-10-29T22:05:20+00:00 Linus Torvalds torvalds@linux-foundation.org 2018-10-29T22:05:20+00:00 93335e5911dbffccd3b74c4d214268c0fd2bc1b0 Pull ARM SoC device tree updates from Arnd Bergmann: "There are close to 800 indivudal changesets in this branch again, which feels like a lot. There are particularly many changes for the NVIDIA Tegra platform this time, in fact more than it has seen in the two years since the v4.9 merge window. Aside from this, it's been fairly normal, with lots of changes going into Renesas R-CAR, NXP i.MX, Allwinner Sunxi, Samsung Exynos, and TI OMAP. Most of the changes are for adding new features into existing boards, for brevity I'm only mentioning completely new machines and SoCs here. For the first time I think we have (slightly) more new 64-bit hardware than 32-bit: Two boards get added for TI OMAP: Moxa UC-2101 is an industrial computer, see https://www.moxa.com/product/UC-2100.htm; GTA04A5 is a minor variation of the motherboards of the GTA04 phone, see https://shop.goldelico.com/wiki.php?page=GTA04A5 Clearfog is a nice little board for quad-core Marvell Armada 8040 network processor, see https://www.solid-run.com/marvell-armada-family/clearfog-gt-8k/ Two additional server boards come with the Aspeed baseboard management controllers: Stardragon4800 is an arm64 reference platform made by HXT (based on Qualcomm's server chips), and TiogaPass is an Open Compute mainboard with x86 CPUs. Both use the ARM11 based AST2500 chips in the BMC. NXP i.MX usually sees a lot of new boards each release. This time there we only add one minor variant: ConnectCore 6UL SBC Pro uses the same SoM design as the ConnectCore 6UL SBC Express added later. However, there is a new chip, the i.MX6ULZ, which is an even smaller variant of the i.MX6ULL, with features removed. There is also support for the reference board design, the i.MX6ULZ 14x14 EVK. A new Raspberry Pi variant gets added, this one is the CM3 compute module based on bcm2837, it was launched in early 2017 but only now added to the kernel, both as 32-bit and as 64-bit files, as we tend to do for Raspberry Pi. On the Allwinner side, everything is again about cheap development boards, usually of the "Fruit Pi" variety. The new ones this time are: - Orange Pi Zero Plus2: http://www.orangepi.org/OrangePiZeroPlus2/ - Orange Pi One Plus: http://www.orangepi.org/OrangePiOneplus/ - Pine64 LTS: https://www.pine64.org/?product=pine-a64-lts - Banana Pi M2+ H5: http://www.banana-pi.org/m2plus.html The last one of these is now a 64-bit version of the earlier Banana Pi M2+ H3, with the same board layout. Similarly, for Rockchips, get get another variant of the 32-bit Asus Tinker board, the model 'S' based on rk3288, and three now boards based on the popular RK3399 chip: - ROC-RK3399-PC: https://libre.computer/products/boards/roc-rk3399-pc/ - Rock960: https://www.96boards.org/product/rock960/ - RockPro64: https://www.pine64.org/?page_id=61454 These are all quite powerful boards with lots of RAM and I/O, and the RK3399 is the same chip used in several Chromebooks. Finally, we get support for the PX30 (aka rk3326) chip, which is based on the low-end 64-bit Cortex-A35 CPU core. So far, only the evaluation board is supported. One more Banana Pi is added with a Mediatek chip: Banana Pi R64 is based on the MT7622 WiFi router platform, and the first product I've seen with a 64-bit Mediatek chip in that market: http://www.banana-pi.org/r64.html For HiSilicon, we gain support for the Hi3670 SoC and HiKey 370 development board, which are similar to the Hi3660 and Hikey 360 respectively, but add support for an NPU. Amlogic gets initial support for the Meson-G12A chip (S905D2), another quad-core Cortex-A53 SoC, and its evaluation platform. On the 32-bit side, we gain support for an actual end-user product, the Endless Computers Endless Mini based on Meson8b (S805), see https://endlessos.com/computers/ Qualcomm adds support for their MSM8998 SoC and evaluation platform. This chip is commonly known as the Snapdragon 835, and is used in high-end phones as well as low-end laptops. For Renesas, a very bare support for the r8a774a1 (RZ/G2M) is added, but no boards for this one. However, we do add boards for the previously added r8a77965 (R-Car M3-N): the M3NULCB Kingfisher and the M3NULCB Starter Kit Pro. While we have lots of DT changes for NVIDIA to update the existing files, the only board that gets added is the Toradex Colibri T20 on Colibri Evaluation Board for the old Tegra2. Synaptics add support for their AS370 SoC, which is part of the (formerly Marvell) Berlin line of set-top-box chips used e.g. in the various Google Chromecast. Only the .dtsi gets added at this point, no actual machines" * tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (721 commits) ARM: dts: socfgpa: remove ethernet aliases from dtsi arm64: dts: stratix10: add ethernet aliases dt-bindings: mediatek: Add bindig for MT7623 IOMMU and SMI dt-bindings: mediatek: Add JPEG Decoder binding for MT7623 dt-bindings: iommu: mediatek: Add binding for MT7623 dt-bindings: clock: mediatek: add support for MT7623 ARM: dts: mvebu: armada-385-db-88f6820-amc: auto-detect nand ECC properites ARM: dts: da850-lego-ev3: slow down A/DC as much as possible ARM: dts: da850-evm: Enable tca6416 on baseboard arm64: dts: uniphier: Add USB2 PHY nodes arm64: dts: uniphier: Add USB3 controller nodes ARM: dts: uniphier: Add USB2 PHY nodes ARM: dts: uniphier: Add USB3 controller nodes arm64: dts: meson-axg: s400: disable emmc arm64: dts: meson-axg: s400: add missing emmc pwrseq arm64: dts: clearfog-gt-8k: add PCIe slot description ARM: dts: at91: sama5d4_xplained: even nand memory partitions ARM: dts: at91: sama5d3_xplained: even nand memory partitions ARM: dts: at91: at91sam9x5cm: even nand memory partitions ARM: dts: at91: sama5d2_ptc_ek: fix bootloader env offsets ... 
Pull ARM SoC device tree updates from Arnd Bergmann:
 "There are close to 800 indivudal changesets in this branch again,
  which feels like a lot. There are particularly many changes for the
  NVIDIA Tegra platform this time, in fact more than it has seen in the
  two years since the v4.9 merge window. Aside from this, it's been
  fairly normal, with lots of changes going into Renesas R-CAR, NXP
  i.MX, Allwinner Sunxi, Samsung Exynos, and TI OMAP.

  Most of the changes are for adding new features into existing boards,
  for brevity I'm only mentioning completely new machines and SoCs here.
  For the first time I think we have (slightly) more new 64-bit hardware
  than 32-bit:

  Two boards get added for TI OMAP: Moxa UC-2101 is an industrial
  computer, see https://www.moxa.com/product/UC-2100.htm; GTA04A5 is a
  minor variation of the motherboards of the GTA04 phone, see
  https://shop.goldelico.com/wiki.php?page=GTA04A5

  Clearfog is a nice little board for quad-core Marvell Armada 8040
  network processor, see
  https://www.solid-run.com/marvell-armada-family/clearfog-gt-8k/

  Two additional server boards come with the Aspeed baseboard management
  controllers: Stardragon4800 is an arm64 reference platform made by HXT
  (based on Qualcomm's server chips), and TiogaPass is an Open Compute
  mainboard with x86 CPUs. Both use the ARM11 based AST2500 chips in the
  BMC.

  NXP i.MX usually sees a lot of new boards each release. This time
  there we only add one minor variant: ConnectCore 6UL SBC Pro uses the
  same SoM design as the ConnectCore 6UL SBC Express added later.
  However, there is a new chip, the i.MX6ULZ, which is an even smaller
  variant of the i.MX6ULL, with features removed. There is also support
  for the reference board design, the i.MX6ULZ 14x14 EVK.

  A new Raspberry Pi variant gets added, this one is the CM3 compute
  module based on bcm2837, it was launched in early 2017 but only now
  added to the kernel, both as 32-bit and as 64-bit files, as we tend to
  do for Raspberry Pi.

  On the Allwinner side, everything is again about cheap development
  boards, usually of the "Fruit Pi" variety. The new ones this time are:
   - Orange Pi Zero Plus2: http://www.orangepi.org/OrangePiZeroPlus2/
   - Orange Pi One Plus: http://www.orangepi.org/OrangePiOneplus/
   - Pine64 LTS: https://www.pine64.org/?product=pine-a64-lts
   - Banana Pi M2+ H5: http://www.banana-pi.org/m2plus.html
  The last one of these is now a 64-bit version of the earlier Banana Pi
  M2+ H3, with the same board layout.

  Similarly, for Rockchips, get get another variant of the 32-bit Asus
  Tinker board, the model 'S' based on rk3288, and three now boards
  based on the popular RK3399 chip:
   - ROC-RK3399-PC: https://libre.computer/products/boards/roc-rk3399-pc/
   - Rock960: https://www.96boards.org/product/rock960/
   - RockPro64: https://www.pine64.org/?page_id=61454
  These are all quite powerful boards with lots of RAM and I/O, and the
  RK3399 is the same chip used in several Chromebooks. Finally, we get
  support for the PX30 (aka rk3326) chip, which is based on the low-end
  64-bit Cortex-A35 CPU core. So far, only the evaluation board is
  supported.

  One more Banana Pi is added with a Mediatek chip: Banana Pi R64 is
  based on the MT7622 WiFi router platform, and the first product I've
  seen with a 64-bit Mediatek chip in that market:
  http://www.banana-pi.org/r64.html

  For HiSilicon, we gain support for the Hi3670 SoC and HiKey 370
  development board, which are similar to the Hi3660 and Hikey 360
  respectively, but add support for an NPU.

  Amlogic gets initial support for the Meson-G12A chip (S905D2), another
  quad-core Cortex-A53 SoC, and its evaluation platform. On the 32-bit
  side, we gain support for an actual end-user product, the Endless
  Computers Endless Mini based on Meson8b (S805), see
  https://endlessos.com/computers/

  Qualcomm adds support for their MSM8998 SoC and evaluation platform.
  This chip is commonly known as the Snapdragon 835, and is used in
  high-end phones as well as low-end laptops.

  For Renesas, a very bare support for the r8a774a1 (RZ/G2M) is added,
  but no boards for this one. However, we do add boards for the
  previously added r8a77965 (R-Car M3-N): the M3NULCB Kingfisher and the
  M3NULCB Starter Kit Pro.

  While we have lots of DT changes for NVIDIA to update the existing
  files, the only board that gets added is the Toradex Colibri T20 on
  Colibri Evaluation Board for the old Tegra2.

  Synaptics add support for their AS370 SoC, which is part of the
  (formerly Marvell) Berlin line of set-top-box chips used e.g. in the
  various Google Chromecast. Only the .dtsi gets added at this point, no
  actual machines"

* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (721 commits)
  ARM: dts: socfgpa: remove ethernet aliases from dtsi
  arm64: dts: stratix10: add ethernet aliases
  dt-bindings: mediatek: Add bindig for MT7623 IOMMU and SMI
  dt-bindings: mediatek: Add JPEG Decoder binding for MT7623
  dt-bindings: iommu: mediatek: Add binding for MT7623
  dt-bindings: clock: mediatek: add support for MT7623
  ARM: dts: mvebu: armada-385-db-88f6820-amc: auto-detect nand ECC properites
  ARM: dts: da850-lego-ev3: slow down A/DC as much as possible
  ARM: dts: da850-evm: Enable tca6416 on baseboard
  arm64: dts: uniphier: Add USB2 PHY nodes
  arm64: dts: uniphier: Add USB3 controller nodes
  ARM: dts: uniphier: Add USB2 PHY nodes
  ARM: dts: uniphier: Add USB3 controller nodes
  arm64: dts: meson-axg: s400: disable emmc
  arm64: dts: meson-axg: s400: add missing emmc pwrseq
  arm64: dts: clearfog-gt-8k: add PCIe slot description
  ARM: dts: at91: sama5d4_xplained: even nand memory partitions
  ARM: dts: at91: sama5d3_xplained: even nand memory partitions
  ARM: dts: at91: at91sam9x5cm: even nand memory partitions
  ARM: dts: at91: sama5d2_ptc_ek: fix bootloader env offsets
  ...
Merge tag 'devicetree-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux 2018-10-26T19:09:58+00:00 Linus Torvalds torvalds@linux-foundation.org 2018-10-26T19:09:58+00:00 b27186abb37b7bd19e0ca434f4f425c807dbd708 Pull Devicetree updates from Rob Herring: "A bit bigger than normal as I've been busy this cycle. There's a few things with dependencies and a few things subsystem maintainers didn't pick up, so I'm taking them thru my tree. The fixes from Johan didn't get into linux-next, but they've been waiting for some time now and they are what's left of what subsystem maintainers didn't pick up. Summary: - Sync dtc with upstream version v1.4.7-14-gc86da84d30e4 - Work to get rid of direct accesses to struct device_node name and type pointers in preparation for removing them. New helpers for parsing DT cpu nodes and conversions to use the helpers. printk conversions to %pOFn for printing DT node names. Most went thru subystem trees, so this is the remainder. - Fixes to DT child node lookups to actually be restricted to child nodes instead of treewide. - Refactoring of dtb targets out of arch code. This makes the support more uniform and enables building all dtbs on c6x, microblaze, and powerpc. - Various DT binding updates for Renesas r8a7744 SoC - Vendor prefixes for Facebook, OLPC - Restructuring of some ARM binding docs moving some peripheral bindings out of board/SoC binding files - New "secure-chosen" binding for secure world settings on ARM - Dual licensing of 2 DT IRQ binding headers" * tag 'devicetree-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (78 commits) ARM: dt: relicense two DT binding IRQ headers power: supply: twl4030-charger: fix OF sibling-node lookup NFC: nfcmrvl_uart: fix OF child-node lookup net: stmmac: dwmac-sun8i: fix OF child-node lookup net: bcmgenet: fix OF child-node lookup drm/msm: fix OF child-node lookup drm/mediatek: fix OF sibling-node lookup of: Add missing exports of node name compare functions dt-bindings: Add OLPC vendor prefix dt-bindings: misc: bk4: Add device tree binding for Liebherr's BK4 SPI bus dt-bindings: thermal: samsung: Add SPDX license identifier dt-bindings: clock: samsung: Add SPDX license identifiers dt-bindings: timer: ostm: Add R7S9210 support dt-bindings: phy: rcar-gen2: Add r8a7744 support dt-bindings: can: rcar_can: Add r8a7744 support dt-bindings: timer: renesas, cmt: Document r8a7744 CMT support dt-bindings: watchdog: renesas-wdt: Document r8a7744 support dt-bindings: thermal: rcar: Add device tree support for r8a7744 Documentation: dt: Add binding for /secure-chosen/stdout-path dt-bindings: arm: zte: Move sysctrl bindings to their own doc ... 
Pull Devicetree updates from Rob Herring:
 "A bit bigger than normal as I've been busy this cycle.

  There's a few things with dependencies and a few things subsystem
  maintainers didn't pick up, so I'm taking them thru my tree.

  The fixes from Johan didn't get into linux-next, but they've been
  waiting for some time now and they are what's left of what subsystem
  maintainers didn't pick up.

  Summary:

   - Sync dtc with upstream version v1.4.7-14-gc86da84d30e4

   - Work to get rid of direct accesses to struct device_node name and
     type pointers in preparation for removing them. New helpers for
     parsing DT cpu nodes and conversions to use the helpers. printk
     conversions to %pOFn for printing DT node names. Most went thru
     subystem trees, so this is the remainder.

   - Fixes to DT child node lookups to actually be restricted to child
     nodes instead of treewide.

   - Refactoring of dtb targets out of arch code. This makes the support
     more uniform and enables building all dtbs on c6x, microblaze, and
     powerpc.

   - Various DT binding updates for Renesas r8a7744 SoC

   - Vendor prefixes for Facebook, OLPC

   - Restructuring of some ARM binding docs moving some peripheral
     bindings out of board/SoC binding files

   - New "secure-chosen" binding for secure world settings on ARM

   - Dual licensing of 2 DT IRQ binding headers"

* tag 'devicetree-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (78 commits)
  ARM: dt: relicense two DT binding IRQ headers
  power: supply: twl4030-charger: fix OF sibling-node lookup
  NFC: nfcmrvl_uart: fix OF child-node lookup
  net: stmmac: dwmac-sun8i: fix OF child-node lookup
  net: bcmgenet: fix OF child-node lookup
  drm/msm: fix OF child-node lookup
  drm/mediatek: fix OF sibling-node lookup
  of: Add missing exports of node name compare functions
  dt-bindings: Add OLPC vendor prefix
  dt-bindings: misc: bk4: Add device tree binding for Liebherr's BK4 SPI bus
  dt-bindings: thermal: samsung: Add SPDX license identifier
  dt-bindings: clock: samsung: Add SPDX license identifiers
  dt-bindings: timer: ostm: Add R7S9210 support
  dt-bindings: phy: rcar-gen2: Add r8a7744 support
  dt-bindings: can: rcar_can: Add r8a7744 support
  dt-bindings: timer: renesas, cmt: Document r8a7744 CMT support
  dt-bindings: watchdog: renesas-wdt: Document r8a7744 support
  dt-bindings: thermal: rcar: Add device tree support for r8a7744
  Documentation: dt: Add binding for /secure-chosen/stdout-path
  dt-bindings: arm: zte: Move sysctrl bindings to their own doc
  ...
dt-bindings: net: add support for Microchip KSZ9131 2018-10-20T00:02:23+00:00 Yuiko Oshino yuiko.oshino@microchip.com 2018-10-18T19:06:02+00:00 806700bab41e9297c6ace1d1d0cabd77b020ad72 Add support for Microchip Technology KSZ9131 10/100/1000 Ethernet PHY Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> 
Add support for Microchip Technology KSZ9131 10/100/1000 Ethernet PHY

Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
dt-bindings: can: rcar_can: Add r8a7744 support 2018-10-15T18:26:29+00:00 Biju Das biju.das@bp.renesas.com 2018-09-27T12:08:48+00:00 700992d361c7912923d1e570681eed65b54a6d9b Document RZ/G1N (r8a7744) SoC specific bindings. Signed-off-by: Biju Das <biju.das@bp.renesas.com> Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Rob Herring <robh@kernel.org> 
Document RZ/G1N (r8a7744) SoC specific bindings.

Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Rob Herring <robh@kernel.org>
Merge ath-next from git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.git 2018-10-14T09:21:43+00:00 Kalle Valo kvalo@codeaurora.org 2018-10-14T09:21:43+00:00 f95cd52476dee761a1a8ebe617dd01793e0eb39c ath.git patches for 4.20. Major changes: ath10k * support NET_DETECT WoWLAN feature * wcn3990 basic functionality now working after we got QMI support 
ath.git patches for 4.20. Major changes:

ath10k

* support NET_DETECT WoWLAN feature

* wcn3990 basic functionality now working after we got QMI support